Alanj

Forum Replies Created

Viewing 15 posts - 586 through 600 (of 757 total)
1 2 3 … 39 40 41 … 49 50 51
  • Author
    Posts
  • May 21, 2007 at 7:34 pm in reply to: Hotpoint FEW 12 #214419
    Alanj
    Participant

    Re: Hotpoint FEW 12

    Hi Hotpnt,

    these screw heads do look pretty corroded.If they don’t screw out will they drill out? 😳

    Alan

    May 21, 2007 at 5:50 pm in reply to: Hotpoint CTD40 #214398
    Alanj
    Participant

    Re: Hotpoint CTD40

    Jim,
    didn’t take the serial no. but machine has three round stats one in middle has solid case ie. no bi metalic discs.

    Alan

    May 21, 2007 at 4:56 pm in reply to: Hotpoint CTD40 #214396
    Alanj
    Participant

    Re: Hotpoint CTD40

    Jim,

    do you know the part number for the ntc or is it part of a kit. There are three stats/cut outs on heater plate.

    Alan

    May 21, 2007 at 4:49 pm in reply to: Hotpoint CTD40 #214395
    Alanj
    Participant

    Re: Hotpoint CTD40

    Thanks iadom for the quick reply.The thing that threw me was the error codes said Pre creasecare was top light=16. making my error code 26.

    Thanks again
    Alan

    May 3, 2007 at 7:12 am in reply to: BEKO WMA 1715S #212504
    Alanj
    Participant

    Re: BEKO WMA 1715S

    Paul,
    just as a matter of interest, was it the motor plug / wiring. 😆
    Alan

    May 3, 2007 at 7:10 am in reply to: Hpt wf860 #212571
    Alanj
    Participant

    Re: Hpt wf860

    Steven,
    have you checked pressure hose for rubbing on tub? Also check discharge hose is high enough to stop syphoning.

    Alan

    May 2, 2007 at 1:45 pm in reply to: Haier RFF5050FF #212493
    Alanj
    Participant

    Re: Haier RFF5050FF

    Further to my last post, if anyone has a manual or parts diagram and list it would be helpful.

    Thanks again
    Alan

    May 2, 2007 at 1:27 pm in reply to: Help: how to replace belt on CTD00 condensor dryer? #212447
    Alanj
    Participant

    Re: Help: how to replace belt on CTD00 condensor dryer?

    Alan,

    you have to remove side of dryer, then remove fan housing cover, fan then comes off by removing spring clip, you will then be able to slide belt over shaft of motor to belt position.Replace in reverse order 😉 .

    Alan

    April 24, 2007 at 4:22 pm in reply to: LG Dishwasher LD12BS6 #211602
    Alanj
    Participant

    Re: LG Dishwasher LD12BS6

    Hi Byan,

    there looked to be a solenoid under the sump which I took to be for diverting water for half load.Is there a switch on that?

    Alan

    April 19, 2007 at 5:00 pm in reply to: ZANUSSI F1256 Washer #211227
    Alanj
    Participant

    Re: ZANUSSI F1256 Washer

    Flash

    Check the module behind facia for blown tracks, most likely cause.

    Alan

    April 19, 2007 at 4:58 pm in reply to: Leaking DWF61 #211229
    Alanj
    Participant

    Re: Leaking DWF61

    Hi Goose,

    have you checked that the lower spray arm is working properly.If they stick or don’t turn freely they tend to spray water out through the door.

    Alan

    April 17, 2007 at 7:03 pm in reply to: Zanussi ZWF1210 Prod 91479128400 #210893
    Alanj
    Participant

    Re: Zanussi ZWF1210 Prod 91479128400

    Hi Guys,

    is there no one speaking to me? 😥

    Alan

    April 16, 2007 at 2:50 pm in reply to: Zannusi DE6544 No Heat #210886
    Alanj
    Participant

    Re: Zannusi DE6544 No Heat

    Hi Monkey,

    have you checked the temperature sensor DST1525033005.

    Alan

    April 15, 2007 at 8:38 pm in reply to: Stoves/Newhome dual fuel cooker DF600SI #210553
    Alanj
    Participant

    Re: Stoves/Newhome dual fuel cooker DF600SI

    Thanks for the replies guys,

    I’ll check out the plastic plugs,but appreciate any other help.

    Alan

    April 15, 2007 at 8:36 pm in reply to: Stoves/Newhome dual fuel cooker DF600SI #210552
    Alanj
    Participant

    Re: Stoves/Newhome dual fuel cooker DF600SI

    wsts

    S/N 005017.

    Alan

  • Author
    Posts
Viewing 15 posts - 586 through 600 (of 757 total)
1 2 3 … 39 40 41 … 49 50 51