alfie

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 61 total)
1 2 3 4 5
  • Author
    Posts
  • March 1, 2013 at 8:35 pm in reply to: ise 5-2 #391306
    alfie
    Participant

    Re: ise 5-2

    Cant see a E10 fault of inverter card,induction motor in that manual

    March 1, 2013 at 6:20 pm in reply to: ise 5-2 #391304
    alfie
    Participant

    Re: ise 5-2

    This is the only one I can find.
    Servicing & diagnostics guide Version 1.0 – December 2008.
    Not applicable to my machine . Is there another version?

    March 1, 2013 at 2:04 pm in reply to: ise 5-2 #391302
    alfie
    Participant

    Re: ise 5-2

    cant find A repair manual for this machine with digital display and induction motor. Is there one?

    November 20, 2012 at 5:40 pm in reply to: Hotpoint Aqualtis AQGD 169 #383923
    alfie
    Participant

    Re: Hotpoint Aqualtis AQGD 169

    The repaired ❗ board from EMW was faulty.
    Tony sent me another one to try and its been working fine.

    October 30, 2012 at 5:52 pm in reply to: Hotpoint Aqualtis AQGD 169 #383921
    alfie
    Participant

    Re: Hotpoint Aqualtis AQGD 169

    That sounds very technical to me and I don’t have any Hotpoint test equipment but if I understand you correctly the board is faulty.

    Thanks Baron

    January 5, 2012 at 7:28 pm in reply to: ISE 1607 #366561
    alfie
    Participant

    Re: ISE 1607

    Would really appreciate some input guys as I’ve not been to a repair on a 1607 before.

    If the thermistor is ok what reading / value should it be?

    If it’s not a heat fault what else should I be looking for?

    Have I read about a reboot somewhere? And if so would this help? & how is it done?

    Is the customer doing something wrong perhaps?

    Cheers in advance

    December 13, 2011 at 12:24 pm in reply to: Hotpoint SDW 60 Dishwasher #365337
    alfie
    Participant

    Re: Hotpoint SDW 60 Dishwasher

    Thanks Jim.
    I know the heater is working and that its not down to earth, that leaves module, relay or wiring prob.Is there a way of testing relay or is it just visual inspection?
    Do you have a wiring diagram I could look at?
    Thanks again.
    Ian

    October 3, 2011 at 6:24 pm in reply to: AW23 #360372
    alfie
    Participant

    Re: AW23

    Cheers for that

    July 26, 2011 at 5:08 pm in reply to: HOTPOINT AQGD 169 MOTOR FAULT #356199
    alfie
    Participant

    Re: HOTPOINT AQGD 169 MOTOR FAULT

    he says no codes are shown in display

    July 8, 2011 at 5:42 pm in reply to: ISE 10 CD 601W #355025
    alfie
    Participant

    Re: ISE 10 CD 601W

    Thanks for that always useful if you’ve never worked on one before.
    Turned out to be a condenser problem. Although customer said they had cleaned the unit they hadn’t done it properly.
    I.e. you could see through the condenser side ways but it was blocked looking length ways. At least they know now.

    A clue was a lot of excess water in the condenser and chamber.

    I also removed the pump to see weather it was blocked. Bit of job, you have to take the back panel off. Not as easy to access as the Hotpoint variants.

    Hope this helps anyone who’s not seen one before.

    March 7, 2011 at 8:32 pm in reply to: ISE 1606 #346461
    alfie
    Participant

    Re: ISE 1606

    Thanks K I will pass that on and await developments. :rolls:

    February 24, 2011 at 8:44 pm in reply to: CANDY T/D CIC 60 #345577
    alfie
    Participant

    Re: CANDY T/D CIC 60

    Read it again Helo.

    Acording to the customer it used to be a push in stay in type switch. In fact when I got there it was stuck in with a piece of gaffer tape and was working .

    February 21, 2011 at 5:52 pm in reply to: LAMONA DISHWASHER #345296
    alfie
    Participant

    Re: LAMONA DISHWASHER

    Is it old enough to have a broken cable or cables at bottom of door panel ❓

    Alfie

    February 21, 2011 at 5:46 pm in reply to: HOOVER HND 6515 #345082
    alfie
    Participant

    Re: HOOVER HND 6515

    Ta for that. A little bed time reading ugh ❗ 😆

    February 20, 2011 at 1:19 pm in reply to: HOOVER HND 6515 #345080
    alfie
    Participant

    Re: HOOVER HND 6515

    How do I put it in to auto test mode Martin ❓

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 61 total)
1 2 3 4 5