alro

Forum Replies Created

Viewing 15 posts - 136 through 150 (of 186 total)
1 2 3 … 9 10 11 12 13
  • Author
    Posts
  • January 12, 2009 at 11:56 pm in reply to: Hotpoint UT47X #273536
    alro
    Participant

    Re: Hotpoint UT47X

    Hi
    could do with the diagram one to go to thurs
    arose.a@sky.com
    cheers alro

    January 12, 2009 at 12:36 am in reply to: Zanussi DE6754 #273480
    alro
    Participant

    Re: Zanussi DE6754

    make sure rinse aid vavle not gone down to earth
    alro

    January 8, 2009 at 11:56 pm in reply to: bosch dishwasher sgs4468/gb27 configuration of module #273422
    alro
    Participant

    Re: bosch dishwasher sgs4468/gb27 configuration of module

    franc
    sent let me know if you do not receive it
    alan

    January 8, 2009 at 8:06 pm in reply to: bosch dishwasher sgs4468/gb27 configuration of module #273420
    alro
    Participant

    Re: bosch dishwasher sgs4468/gb27 configuration of module

    need email adress to send to
    cheers alro

    January 7, 2009 at 12:39 am in reply to: LG WM12397TD motor problems. #273063
    alro
    Participant

    Re: LG WM12397TD motor problems.

    Had same fault a bit ago replaced stator with hall sensor in it worked find no stammer or clunk semes are the cheapest half the cost of connect
    cheers alro

    January 5, 2009 at 11:17 pm in reply to: HOTP FFA74 COMPRESSOR TOC #272540
    alro
    Participant

    Re: HOTP FFA74 COMPRESSOR TOC

    thanks ian
    address sent to you
    cheers alan

    December 30, 2008 at 11:03 pm in reply to: HOTP FFA74 COMPRESSOR TOC #272538
    alro
    Participant

    Re: HOTP FFA74 COMPRESSOR TOC

    cheers alro

    December 13, 2008 at 12:31 pm in reply to: Diplomat APM6855 F/Freezer fan motor #271432
    alro
    Participant

    Re: Diplomat APM6855 F/Freezer fan motor

    Simon
    put a live & neutral direct to it def motor us jist need a cheaper version pt number
    alro

    November 29, 2008 at 12:20 am in reply to: Servis M320 #270057
    alro
    Participant

    Re: SERVICE M320

    Make sure belt is tight
    alro

    November 23, 2008 at 6:01 pm in reply to: zanussi zwf1010w #269097
    alro
    Participant

    Re: zanussi zwf1010w

    try cold water valve
    alan

    November 22, 2008 at 5:32 pm in reply to: LG WM14225FD MOTOR STAMMER #268998
    alro
    Participant

    Re: LG WM14225FD MOTOR STAMMER

    Cheers
    gents for all replies changded stator all ok drum turns fine
    alan

    November 19, 2008 at 7:19 pm in reply to: LG WM1480FHD Bearings #268941
    alro
    Participant

    Re: LG WM1480FHD Bearings

    Treat it same as a zanussi everthing throw front thou like wma machines
    cheers alro

    November 19, 2008 at 6:56 pm in reply to: LG WM14225FD MOTOR STAMMER #268996
    alro
    Participant

    Re: LG WM14225FD MOTOR STAMMER

    SMARTIN
    thanx for reply now stuck betweem pcb and stator again as the motor dose shimmer when 240v from pcb but stops is this the same as you have had
    alro

    November 14, 2008 at 12:32 am in reply to: Smeg DWI710E1 cannot programme #268388
    alro
    Participant

    Re: Smeg DWI710E1 cannot programme

    chris
    thank for reply no water in base & the micro switch on atiflood is not in op or i can use my screwi and lift it up to operate the pump
    cheers alro

    November 14, 2008 at 12:28 am in reply to: samsung srl3916bss problem #268360
    alro
    Participant

    Re: samsung srl3916bss problem

    remove rear in freezer 4 screws ,remove 2screws fan unplug connectors plus the 8way back left side near motor flap remove cover to expose the evap,you will find defrost heater on evap is o/c you properly have to change evap with heater as it may not come as a part + regas
    alro

  • Author
    Posts
Viewing 15 posts - 136 through 150 (of 186 total)
1 2 3 … 9 10 11 12 13