alster

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 65 total)
1 2 3 4 5
  • Author
    Posts
  • September 4, 2018 at 7:13 pm in reply to: Hotpoint double oven #457750
    alster
    Participant

    Re: Hotpoint double oven

    I would agree with iadom. Its probably the plaset short shaft fan motor. & the alternative from connect appears to be identical.

    August 16, 2018 at 6:47 am in reply to: Belling cooker 616 clock volume #457375
    alster
    Participant

    Re: Belling cooker 616 clock volume

    Don’t think I’ve ever come across an oven clock with a volume control. Alan

    August 14, 2018 at 3:16 pm in reply to: Intergrated fridge freezer door hinges convert to slide door #457321
    alster
    Participant

    Re: Intergrated fridge freezer door hinges convert to slide

    I think you may have miss read the question! I think what’s being asked is if you could re hang the cupboard doors and then buy a fridge with sliders. So yes- peovided you have the skills to rebate the doors to fit cupboard door hinges and correctly fit them. The actual housing should be the same size- fridges with sliders are not as wide to allow for the cupboard door hinges.

    July 12, 2018 at 12:09 pm in reply to: Hotpoint WMBF742 goes dead #456791
    alster
    Participant

    Re: Hotpoint WMBF742 goes dead

    As above & have a good look at the suppressor- ive had a couple where there’s a poor/ overheating connector plug.

    July 10, 2018 at 12:44 pm in reply to: DeDietrich DHD900 extractor #456735
    alster
    Participant

    Re: DeDietrich DHD900 extractor

    I’ve all ready done a bit of research & got a part no. For the board-i was just uneasy about ordering it!!!

    July 9, 2018 at 8:52 pm in reply to: DeDietrich DHD900 extractor #456733
    alster
    Participant

    Re: DeDietrich DHD900 extractor

    Yes. Qualtex have the pcb in stock but it’s about £150 so I’m being a bit cautious!!

    July 9, 2018 at 7:41 pm in reply to: DeDietrich DHD900 extractor #456731
    alster
    Participant

    Re: DeDietrich DHD900 extractor

    Thanks for reply but PCB & power supply board both look fine. Alan

    June 27, 2018 at 3:44 pm in reply to: Indesit XWA91683 #456597
    alster
    Participant

    Re: Indesit XWA91683

    It’s not on child lock is it ??

    June 22, 2018 at 11:51 am in reply to: Zanussi ZWD71460NW Dryer not heating #456494
    alster
    Participant

    Re: Zanussi ZWD71460NW Dryer not heating

    Haven’t looked up the exact model but check for earth fault on dryer element or wires broken on thermistor at the bottom of the condenser.

    June 19, 2018 at 7:22 pm in reply to: Neff single oven door issue #456410
    alster
    Participant

    Re: Neff single oven door issue

    I would agree with neon. Those doors do ‘snap shut’ when the hinges are good.

    June 5, 2018 at 3:53 pm in reply to: bush dryer v7sdw #456192
    alster
    Participant

    Re: bush dryer v7sdw

    Bit late now but did you check the motor capacitor??

    June 3, 2018 at 2:44 pm in reply to: Hotpoint tdc32s condenser dryer #456168
    alster
    Participant

    Re: Hotpoint tdc32s condenser dryer

    Is the rear drum seal ok?

    May 22, 2018 at 3:26 pm in reply to: Van Racking #456004
    alster
    Participant

    Re: Van Racking

    Here we go..(hopefully!!)

    May 22, 2018 at 2:15 pm in reply to: Van Racking #456003
    alster
    Participant

    Re: Van Racking

    I use Festool systainer boxes. Not the cheapest but they come in various sizes and all lock together. Best prices seem to be anglia tool centre. You can see their range online. I’ll do a pick if i can work out how!!

    May 21, 2018 at 4:30 pm in reply to: Moffat MSS601X wiring diagram #455971
    alster
    Participant

    Re: Moffat MSS601X wiring diagram

    Have you meggered it??? Earth leaks will light up a neon.

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 65 total)
1 2 3 4 5