chitts

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 86 total)
1 2 3 4 5 6
  • Author
    Posts
  • April 19, 2018 at 6:08 am in reply to: Miele G653 SCVI PLUS dishwasher #455355
    chitts
    Participant

    Re: Miele G653 SCVI PLUS dishwasher

    Broken wire in door harness? Had same fault and that was the cause.

    February 14, 2018 at 3:49 pm in reply to: Hotpoint FDW20 LED’s 2 & 4 flashing #453949
    chitts
    Participant

    Re: Hotpoint FDW20 LED’s 2 & 4 flashing

    The strange thing is the machine heats and completes the cycle in the normal time!! Fault code only after cycle finishes.
    I’ve watched it for 20 mins to prove the heater is working.

    July 1, 2017 at 10:52 am in reply to: WVD24520GB/01 #410714
    chitts
    Participant

    Re: WVD24520GB/01

    Yes, but armature had dud segments, so write off after all.

    June 30, 2017 at 3:44 pm in reply to: WVD24520GB/01 #410712
    chitts
    Participant

    Re: WVD24520GB/01

    Thanks. Got to that eventually.

    June 27, 2017 at 3:24 pm in reply to: WVD24520GB/01 #410710
    chitts
    Participant

    Re: WVD24520GB/01

    Hi. Did anyone find the answer to this fault? I have been to one doing the same, and all the connectors seem fine I assume it’s the module. As the board was replaced a couple of years ago it seems odd!

    June 13, 2017 at 10:04 am in reply to: Whirlpool ADG7470/2 8542 748 5000 Starts then cuts out #448100
    chitts
    Participant

    Re: Whirlpool ADG7470/2 8542 748 5000 Starts then cuts out

    Sorry Dave, I missed the 1!
    Thanks for the info, I’ll check whether I can get into test cycle. Just seems odd, no LED’s except on/off, which goes off after the initial pump time.

    May 31, 2017 at 5:43 pm in reply to: Bosch SMS58E22GB/85 E14 fault #447789
    chitts
    Participant

    Re: Bosch SMS58E22GB/85 E14 fault

    Thanks Martin. Yes have changed the reed switch. It turned out being a bad contact on the board. I guess it’s been standing in a damp place. Anyway, by pulling off all the connections and squeezing them a bit, finally 3 loads perfect!!

    December 21, 2016 at 5:51 pm in reply to: Ignis AKL907 Child lock on and can’t release #443943
    chitts
    Participant

    Re: Ignis AKL907 Child lock on and can’t release

    Thanks. I thought that when I called to see it. She’s bought a new one which is even more complicated to use!!

    October 6, 2016 at 8:04 am in reply to: AEG 64840L 914524560/00 Cuts out after door locks #441522
    chitts
    Participant

    Re: AEG 64840L 914524560/00 Cuts out after door locks

    Meggered and checked again when it decided to work. It’s now stopped again after a couple of loads. Thought maybe a loose conection, but everything seems tight. It’s in a retirement complex, so gets used heavily. Seems like control board fault, but would like to prove it first.

    July 7, 2016 at 7:06 am in reply to: LG F1403YD5 noisy when slowing down on spin #439127
    chitts
    Participant

    Re: LG F1403YD5 noisy when slowing down on spin

    Thanks for your ideas. I think the spline stripping is most likely, but I don’t have to look now as customer has ordered a new machine!

    June 24, 2016 at 4:56 pm in reply to: Lamona dishwasher LAM8602 #438544
    chitts
    Participant

    Re: Lamona dishwasher LAM8602

    Had a similar one today, no wash after filling. Broken wires in the door harness!
    I thought manufacturers had this sorted, obviously not. Dishwasher fires next?

    June 3, 2016 at 11:34 am in reply to: Bosch WTA74200GB/01 #438134
    chitts
    Participant

    Re: Bosch WTA74200GB/01

    Thanks. I can go prepared.

    June 2, 2016 at 3:26 pm in reply to: Miele G4100 57/100799235 Dishwasher #437994
    chitts
    Participant

    Re: Miele G4100 57/100799235 Dishwasher

    That’s most likely problem. If the filter isn’t locked down all the crap gets through!

    February 21, 2016 at 8:25 pm in reply to: miele w916 tap light coming on—still #435409
    chitts
    Participant

    Re: miele w916 tap light coming on—still

    Had the same problem a few weeks ago. Traced to air lock in water supply. Disconnected hose at supply and flushed for a minute until “spluttering” stopped, reconnected and fine ever since

    September 6, 2015 at 6:17 am in reply to: Miele W3830 Paragon Plus #430009
    chitts
    Participant

    Re: Miele W3830 Paragon Plus

    Clean the breather tubes from top to bottom!

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 86 total)
1 2 3 4 5 6