cornwell40

Forum Replies Created

Viewing 15 posts - 1,351 through 1,365 (of 1,670 total)
  • Author
    Posts
  • in reply to: New World DFEO70 oven #166075
    cornwell40
    Participant

    Re: New World DFEO70 oven

    Thanks Dave 🙂

    Tony C

    in reply to: Now AvailableTo Pre-Order #162734
    cornwell40
    Participant

    Re: Now AvailableTo Pre-Order

    Thanks for that.
    I’d better get some orders in now 😳


    Tony C

    in reply to: getting manuals or cds whitegoods #152305
    cornwell40
    Participant

    Re: getting manuals or cds whitegoods

    😳 Er wots emule?

    in reply to: CDA CW494/1 #164273
    cornwell40
    Participant

    Re: CDA CW494/1

    Thanks for info 🙂 .

    Tony C

    in reply to: chanelle falling apart #162835
    cornwell40
    Participant

    Re: chanelle falling apart

    Simon46 wrote

    Did one where i ran machine with sump hose off filter assembly in customers landscaped rear garden with garden hose in soap drawer.

    Ah!!! memories. 😆 😆

    Tony C

    in reply to: Public Information #163943
    cornwell40
    Participant

    Re: Public Information

    This kind of puts it in context to me.
    Yesterday I had a customer ring up for a float switch for an indesit dishwasher. I asked why as I’d never had to fit one and she didn’t sound that clued up.
    She had rung Indesit to find out what the fault code on the dishwasher meant and she was told its the float switch.
    Rather than sell her a float switch I explained about leaks, water in the base, why the switch works etc.
    She rang back to book a call in.
    Later a guy rang to say he wanted a belt for a Hotpoint WM. I asked a few questions and decided it was the bearings gone. He said ‘ Oh I’ll just scrap it and buy new, thanks for that I’ll call you if anything else goes wrong’. He has mates, family, other people will hear that you are helpful and know what your’e talking about, i.e they’ll reccomend you to others.
    It promotes your business.
    Doesn’t matter who the info comes from (if it’s the right info) people remember where it came from and reccomend.
    They don’t always act on the information given. I’ve had people ring me with quite a detailed diagnosis they’ve got off UKW and when asked why they didn’t want to do the (quite simple) job themselves they were just curious as to what caused it.

    Tony C

    in reply to: The Mind Reader #164160
    cornwell40
    Participant

    Re: The Mind Reader

    Tried it loads of times and it’s right onevery one…spooky.

    Tony C

    in reply to: Bosch SMI6022GB/03 Dishwasher overfill #163529
    cornwell40
    Participant

    Re: Bosch SMI6022GB/03 Dishwasher overfill

    Been back to this one today armed with CJ’s info and fault immediately apparent. The return from the microswitch had melted into the tar on the door. Looked ok at first glance but the pull test proved the fault 😉 .

    Thanks Mr Jameson.

    Tony C

    in reply to: Bosch d/w heater failures #164108
    cornwell40
    Participant

    Re: Bosch d/w heater failures

    Sorry Mike, I think Eastlemark means the heater box itself not the pcb fault 😉 .

    Only ever had a couple of the boxes go, but they have both been in the last couple of months.

    Tony C

    in reply to: Stoves thermostat coming by tortoise #163996
    cornwell40
    Participant

    Re: Stoves thermostat coming by tortoise

    Masterpart do the TS14236 stat for £5.99 as well. Same as most whirlpool single ovens.


    Tony C

    in reply to: Now AvailableTo Pre-Order #162732
    cornwell40
    Participant

    Re: Now AvailableTo Pre-Order

    Kheath wrote

    We can do Blackpool, will have to ask though, is it any use to you.

    Blackpool is fine if thats ok. Its a temporary thing, once my house FINALLY sells 👿 there’ll be no probs on deliveries.
    Tony C

    in reply to: Hpt 9506 stat #163859
    cornwell40
    Participant

    Re: Hpt 9506 stat

    Its the old type stat with one tag left and two tags right. They are saying it only sticks on the 40deg prog, even on a 90deg will advance through then stick on the forty. Heater and 85deg stat ok. Economy works ok(not checked P/switch 😳 )


    Tony C

    in reply to: Now AvailableTo Pre-Order #162729
    cornwell40
    Participant

    Re: Now AvailableTo Pre-Order

    Is there a level one in the Preston area that could take delivery of a couple of machines for me. At the moment I don’t know where I am from one day to the next and the area is too open to have them ‘left’ somewhere. They would be picked up asap.

    Tony C

    in reply to: chanelle falling apart #162830
    cornwell40
    Participant

    Re: chanelle falling apart

    Another good reason not to cross by the Chanelle tunnel if it’s falling apart. 😆

    Tony C

    cornwell40
    Participant

    Re: How long do you give yourself for a job in a customers h

    I was told in the dim and distant past by a Hotpoint manager that I was doing too many 20 minute calls. This was at the time of the early 95 flush doors when door wont open was up to four calls a day, and the rest were brushes.

    Tony C

Viewing 15 posts - 1,351 through 1,365 (of 1,670 total)