Criscold

Forum Replies Created

Viewing 15 posts - 766 through 780 (of 816 total)
1 2 3 … 51 52 53 54 55
  • Author
    Posts
  • April 1, 2011 at 4:03 pm in reply to: Bosch WFR3269GB/05 #348390
    Criscold
    Participant

    Re: Bosch WFR3269GB/05

    Thanks Martin

    I have now got the machine in the workshop and managed to find test cycle info and comes up with error 10 but can’t find this error not listed – can anyone help on this.

    I will post test info later

    Thanks

    Colin

    March 30, 2011 at 6:16 pm in reply to: Stoves E1000DL grill element #348213
    Criscold
    Participant

    Re: Stoves E1000DL grill element

    I think it may be ADP5613 model 058560032 check http://www.hygenadiplomatspares.co.uk/

    Colin

    March 29, 2011 at 5:22 pm in reply to: zanussi zdm868b grill element #348120
    Criscold
    Participant

    Re: zanussi zdm868b grill element

    The Grill element listed is 3570339014 but this comes up as obsolete. had one last month and used Qualtex ELE2031 slight alteration to the support bar plus add link to common terminal.

    Colin

    March 23, 2011 at 7:09 pm in reply to: Zanussi FJS 1397W Spin issues – #347741
    Criscold
    Participant

    Re: Zanussi FJS 1397W Spin issues –

    Speed Potentiometer or connections between that and the timer might be worth a check.

    Colin

    March 22, 2011 at 3:11 pm in reply to: AEG 72630W 914002096-01 bearing kit #347685
    Criscold
    Participant

    Re: AEG 72630W 914002096-01 bearing kit

    Bearings And Seal are
    5423255206 – 6205
    5423306207 – 6206
    1249685007 Seal

    March 22, 2011 at 9:15 am in reply to: zwd12270w not starting #347669
    Criscold
    Participant

    Re: zwd12270w not starting

    Can you get into diagnostics ?

    Colin

    March 20, 2011 at 8:09 pm in reply to: Replacement Themostat for Triciy oven Model 2159 #347510
    Criscold
    Participant

    Re: Replacement Themostat for Triciy oven Model 2159

    Sorry not correct thermostat

    Colin

    March 20, 2011 at 8:02 pm in reply to: Replacement Themostat for Triciy oven Model 2159 #347509
    Criscold
    Participant

    Re: Replacement Themostat for Triciy oven Model 2159

    Qualtex list MO Thermostat for that oven QUACS35

    Colin

    March 18, 2011 at 8:36 am in reply to: Belling XOU252SS Ser: 058585125 Hob Problem #347149
    Criscold
    Participant

    Re: Belling XOU252SS Ser: 058585125 Hob Problem

    Single Regulators fgor each plate Pt No. stv082611723 – nice simple job.

    Colin

    March 17, 2011 at 6:17 pm in reply to: Belling XOU252SS Ser: 058585125 Hob Problem #347147
    Criscold
    Participant

    Re: Belling XOU252SS Ser: 058585125 Hob Problem

    Are you sure that this model Number is the hob as I can only find ovens listed under this?

    Colin

    March 17, 2011 at 6:10 pm in reply to: Diplomat/Whirlpool dw motor #347296
    Criscold
    Participant

    whirlpool dw motors

    I agree about the clips but now use Norma clips they fit well on these motors http://www.merlinmotorsport.co.uk/COOLI … index.html

    Colin

    March 17, 2011 at 5:56 pm in reply to: w/pool adp8000 f3 #347030
    Criscold
    Participant

    Re: w/pool adp8000 f3

    Is this the heater that is fitted directly onto the motor if so lay machine on LH side and remove base panel – Remove motor assy – replace heater then refit motor assy easy job

    Colin

    March 15, 2011 at 5:05 pm in reply to: esl4114 #347115
    Criscold
    Participant

    Re: esl4114

    This is an old style machine and could possible be a timer fault but would check as you stated the heating along with filling and pumping, also that the siphon tubes are not blocked, these can cause a lot of problems with timer sticking

    Colin

    March 12, 2011 at 7:25 pm in reply to: DE6754 , NO HEAT #346995
    Criscold
    Participant

    Re: DE6754 , NO HEAT

    Did you test heater circuit from connections on module and also check solder joints on module around the relay?

    Colin

    March 8, 2011 at 7:16 pm in reply to: Lux Stat #346396
    Criscold
    Participant

    Re: Lux Stat

    The cooling fan stat is 3570560056 rated 115/100c NA – open circuit until reaching temperature. then brings fan into operation. the other stat is NC and this is a large klixon overheat stat – I had one to fit fit today.

    Colin

  • Author
    Posts
Viewing 15 posts - 766 through 780 (of 816 total)
1 2 3 … 51 52 53 54 55