Criscold

Forum Replies Created

Viewing 15 posts - 751 through 765 (of 816 total)
  • Author
    Posts
  • in reply to: John Lewis Condenser Dryer with compressor? Need manual. #349916
    Criscold
    Participant

    Re: John Lewis Condenser Dryer with compressor? Need manual.

    I understand that you can get the base complete with heatpump for only £460 – what a bargain

    in reply to: Zanussi ZDT6053 fault code ???????? #349851
    Criscold
    Participant

    Re: Zanussi ZDT6053 fault code ????????

    Yes its a with a heat problem – let me have your email and I can send you some info

    Colin

    in reply to: Indesit WIB111 Drum Lifter/Paddle #349676
    Criscold
    Participant

    Re: Indesit WIB111 Drum Lifter/Paddle

    Thanks Bazza500

    I ordered this part and it was the correct one but Indesit phoned me back last night and the girl on the phone was adamant that they only fitted a 10 or 12 hole paddle to this model.

    Thanks again for your help

    Colin

    in reply to: Indesit WIB111 Drum Lifter/Paddle #349675
    Criscold
    Participant

    Re: Indesit WIB111 Drum Lifter/Paddle

    Great that looks like the one

    Thanks for your help

    Colin

    in reply to: Indesit WIB111 Drum Lifter/Paddle #349673
    Criscold
    Participant

    Re: Indesit WIB111 Drum Lifter/Paddle

    Yes this is the only one listed at Qualtex but is 10 holes and 180×55.

    Thanks

    Colin

    in reply to: zanussi little dishwasher b22 #349293
    Criscold
    Participant

    Re: zanussi little dishwasher b22

    Inlet valve neutrel fed via door switch,boil dry stat (should be red/white wire + white wire) and pressure switch, Live feed via timer contacts. If drawings req let me have your email.

    Colin

    in reply to: AEG Cooker Model B4101/4/M #349232
    Criscold
    Participant

    Re: AEG Cooker Model B4101/4/M

    If the time is not set on the clock the relay will not allow the oven to operate, as the clock has gone off I would agree that this would probably be the reason for the failure. Looking at the diagram it appears that the clock is connected direct across the mains. I think I would temporally bypass the relay connections to prove the fault. If you would like a diagram let me have you email address.

    Colin

    in reply to: AEG Santo N7 1840-41 (925771703-01) #348861
    Criscold
    Participant

    Re: AEG Santo N7 1840-41 (925771703-01)

    Hi

    If the unit is running and the freezer is cold, I would think you would probably have a system fault, do you know what temperature is in the freezer? I don’t think a module would make any difference on this unit.

    Colin

    in reply to: Electrolux ESL6225 dishwasher #348833
    Criscold
    Participant

    Re: Electrolux ESL6225 dishwasher

    Are you sure its the matrix leaking and not the air guide in the roof thats leaking down the side? thats a common problem with these.

    Colin

    in reply to: WHIRLPOOL AKZ456IX FO3 CODE #348700
    Criscold
    Participant

    Re: WHIRLPOOL AKZ456IX FO3 CODE

    Hi
    http://www.justanswer.com/uk-appliance/ … -good.html
    Just googled the model and found this ?

    Colin

    in reply to: Electrolux W365H EXACTA CONTROL #348641
    Criscold
    Participant

    Re: Electrolux W365H EXACTA CONTROL

    Just did a quick Google as not listed under domestic and found this, hope its correct

    http://www.laundrysystems.electrolux.co … rus_EN.pdf

    Good Luck

    Colin

    in reply to: De Dietrich DVH640JU1 DISHWASHER #348620
    Criscold
    Participant

    Re: De Dietrich DVH640JU1 DISHWASHER

    Found Instruction Book d03 Heating Fault – http://www.dedietrich.co.uk/documents/DVH640J.pdf

    Colin

    in reply to: Zanussi zwi 2125 1 minute to go #348557
    Criscold
    Participant

    Re: Zanussi zwi 2125 1 minute to go

    Could you get into diagnostics?

    in reply to: AEG – SANTO 75348 – PROD: 928405224 #318859
    Criscold
    Participant

    Re: AEG – SANTO 75348 – PROD: 928405224

    Glad to hear all went OK, did a zanussi about 15 years ago got the hissing spent another couple of hours repairing pipe but never got anymore work from customer. still wonder if it ever worked afterwards.

    Colin

    in reply to: Bosch WFR3269GB/05 #348392
    Criscold
    Participant

    Re: Bosch WFR3269GB/05

    I was hoping that error 10 would get me nearer the problem, As the cables seem to be ok I’m thinking that I may have damaged the interlock, there are 7 connections on the lock and it would help if I could get hold of a diagram or information on the connections to the lock. If anybody could help with this.

    Thanks

    Colin

Viewing 15 posts - 751 through 765 (of 816 total)