[DAR01]

Re: HELP BUILT IN DISHWASHER PARTS

Thanks for the info, anyone got a breakdown of the parts, if so are the springs attached directly between cabinet and door hinges?

(Haven’t been to see this machine yet but I don’t want to have to take it out twice,built in I think.)

Where can I get the parts from, supplier/phone no if possible?

Many thanks

Mike

[DAR01]

Re: Zanussi Bearing Change

Sold a couple of Bendix machines this week,took the top off, outer drum welded together in middle,am I cutting my mouth?

Is this the future for the Electrolux range?

Mike

[DAR01]

Re: Days like these.

Re zan FL1085 I usually replace the spider and bearings on this machine.
Spider UNT19 Bearings BKT08 QUALTEX.

I usually find that the Brushes will probably need replacing,if they have not been replaced previously.

Worth checking before you do the bearings as the total repair may not be cost effective.

MIKE

[DAR01]

Re: Zanussi Tc7102W not heating (rotary switch?)

Have you checked the stat near the top of the front housing between front of machine and the drum. not easy to get at though,it may be open circuit.

Mike

[DAR01]

Re: PROLINE EF6200B/1

Thanks Dave 😀 😀 😀

Mike

[DAR01]

Re: PROLINE EF6200B/1

Thanks Penguin, did a search on Connections using the Comet Part No. came up with Order Code 5031688681484 Brandt m/o stat ckr OME24 £20.49 +vat.

I assume this is the correct stat can anyone confirm please.

MIKE

[DAR01]

Re: WMA 20P replacement Drum /bearings

I always use an angle grinder to sort out the bolts on the spider, eg.cut through the spider arms as close as you can to the outer part of the drum. (make sure you use some safety goggles) Fit new spider and back part of drum with new bearings / seal already fitted.

I always refer the customer to the fact that they can have the job done by Hotpoint for aprox £90 if the machine is under 5 years old,under the free parts gaurantee, Haa, Haa.

It depends on how desperate the customer is to having the machine fixed,I can usually have it fixed next day, they usually have to wait several days before a Hotpoint engineer can call.

Most customers are happy with this because they save money in the long run if they are prepared to wait for Hotpoint,but the advise offered my me stands in good stead after the gaurantee runs out because they come back to me, for advice or repairs.

Mike

[DAR01]

Re: Hotpoint Power Unit

A new one, is she on drugs? £338.40 my price from Electruepart, sorry its not available. 🙁 🙁 🙁

[DAR01]

Re: HOMARK 01-511050 BUILT IN OVEN

Thanks Dave got one from D S Supplies (Stoke on Trent) £3.50 plus VAT.

Thanks Again

Mike

[DAR01]

Re: SMEG DWF409WH D/WASHER

Thanks for the info,spot on with the diagnosis.customer amazed that I was able to fix it straight away.

Especially as he is an X ray machine service engineer.

It’s easy when you know the answer. 🙂 🙂 🙂

[DAR01]

Re: SMEG DWF409WH D/WASHER

Thanks I’ll let you know what Ifind.

[DAR01]

Re: Interesting problem

Must be freezians

[DAR01]

Re: Top pseudonym!

I used to have a boss called Mike Hunt. 😀 😀 😀

[DAR01]

Re: Interesting problem

How do you get them in the freezer? 😀 😀 😀

[DAR01]

Re: Bosch SPS5122 filling with clean water after cycle

Have you tried turning off the water supply to the machine, if it stops filling then it is the inlet valve on the machine that is faulty.

[Author]

Posts