DDSDDS

Forum Replies Created

Viewing 15 posts - 286 through 300 (of 506 total)
  • Author
    Posts
  • in reply to: Zanussi Nexus FL-1282 programme problem #225801
    DDSDDS
    Participant

    Re: Zanussi Nexus FL-1282 programme problem

    when it sticks can you hear any noises
    ticking buzzing or intake of water
    y guess would be your machine is siphoning the water out of your stand pipe during the cycle all you have to do is raise the waste further up the stand pipe
    let us know how u get on if it is that:)

    in reply to: Soap filling up outlet pipe #225981
    DDSDDS
    Participant

    Re: Soap filling up outlet pipe

    i had this a load of times although curiously only on indesit machines i have no idea why probably just a coincidence but you need to loop the outlet pipe higher than the point it attaches to your sink so nothing will flow back from the sink.

    in reply to: Hpt WF860 IN TEST MODE #225954
    DDSDDS
    Participant

    Re: Hpt WF860 IN TEST MODE

    oh trapdoor my fave

    in reply to: No spin #225881
    DDSDDS
    Participant

    Re: No spin

    is there any water left in the drum at the end of the cycle?
    and does it fill at the begining of the cycle
    these machines are prone to problems with the module which is the electronics have dig around on here and search for servis module should give you some clues
    if you suspect it is still full of water have you checked the filter it is on the bottom right as you face the machine
    have a towel and a mop ready as any water left in the machine will most likely come flooding out

    in reply to: keeping appliance #225865
    DDSDDS
    Participant

    Re: keeping appliance

    all taken on board lads, perhaps caller id is a good idea as we get a lot of old dodderys forget their number and 1471 may as well be on speed dial
    as for the drop off we just dont get many people drop them off here we normally call out happens maybe once or twice a month i think i will take the fridge home and put it in my garage less likely to get damaged then

    in reply to: No spin #225879
    DDSDDS
    Participant

    Re: No spin

    i have found this to be a dodgy belt or more often the module sometimes they can be repaired new modules are expensive but repairs are normally possible i think there is a someone on here called emw that does module repairs

    in reply to: Fridge Odour #225577
    DDSDDS
    Participant

    Re: Fridge Odour

    did you paint when you decorated is there any paint on the compressor or radiator heating up when its running causing your smell
    do tell

    in reply to: no marks on program dial #225746
    DDSDDS
    Participant

    Re: no marks on program dial

    if you say it is missing 1-5 on the dial then i can tell you i have a performa in my shop its number 4 wash is opposite the centre of 10 and 11 ie put ten and eleven at the very bottom you should then have a 40 wash which is the main wash on this machine

    there is no tell though if the one i am looking at is the same as yours without more details but a dial fitted would be the best option to avoid any problems

    in reply to: washing machine stops after 10secs & wont spin #225845
    DDSDDS
    Participant

    Re: washing machine stops after 10secs & wont spin

    servis+odd behaviour=module
    simple equation that has served me well
    as kwatt said they aint cheap and normally it is not worth the repair these machines not being the most relaible anyway

    DDSDDS
    Participant

    Re: Hoover se220 – not spinning (and now a slight burning sm

    replace the brushes before you continue using it as they probably was not stuck more likely at the very end of there life continued use with rubbish brushes could cause more damage:)

    in reply to: Square pegs…. #225168
    DDSDDS
    Participant

    Re: Square pegs….

    done all levels 4000 moves exactly 130 fails 2 and a half hours was so proud till i realised TWO AND A HALF HOURS where did it all go:S

    in reply to: Connect next day delivery? Am I just unlucky? #200255
    DDSDDS
    Participant

    Re: Connect next day delivery? Am I just unlucky?

    been using connect for almost 12 months now always seems really quick to arrive never anything late although odd item seems to stay on backorder forever and a day even though we may re-order the same part next time and have it arrive but generally good dealing with them

    in reply to: Hotpoint WF 440 #225227
    DDSDDS
    Participant

    Re: Hotpoint WF 440

    we call it the f08 of death

    in reply to: Freezer making a ticking noise #225232
    DDSDDS
    Participant

    Re: Freezer making a ticking noise

    FROST FREE
    can be misleading i find a large {e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} of my f/f callouts are frozen up and the customer generally gobsmacked when he is told to defrost.

    in reply to: Made me think. #223640
    DDSDDS
    Participant

    Re: Made me think.

    about two years ago i had a phone call asking me if the money spent in a bar in australia was anything to do with me as i have never been there said no and the banks sorted it, although a friend of mine once paid for a television which was a shock to him when his statement came through and he found out he got all his money back too though

Viewing 15 posts - 286 through 300 (of 506 total)