[DentedPorsche]

Thanks for that. I’ve got the user manuals but not the service manual.
I did try all the programs but Ithe compressor never runs. (don’t think it’s getting power).
Not to worry, thanks for trying.

[DentedPorsche]

Re: whirlpool oven service manual if possible

Missing a number on the 85 number.

What information do you need?
Parts list, wiring diagram, or??

[DentedPorsche]

Re: Whirlpool AWZ3303 T/D Modified Switch Wiring Connections

Hiya,
Long time since I had to do one of these.
The new switch will have 4 connections, 2 for the door switch and 2 for the start.

If I remember correctly, 1 and 3 are for the door switch and 5 and 6 for the start button.

You need to identify on the original which pair of wires are for the door switch, fit them to 1 and 3, the other 2 then (obviously) go to 5 and 6.

Hope this helps

[DentedPorsche]

Re: hotpoint oven code

Hiya,
The codes I have for Hotpoint single ovens show this code to be a problem concerning the potentiometer regulating the temperature.
The fault is discovered after 1 minute from the moment that the oven is turned on.

Unfortunately, can’t say for sure that this covers your machine, but, I’ve no other oven codes.

Hope it helps.

[DentedPorsche]

Re: Diplomat ADP8322 f7 f6 f5 after repair

ADP8322 has no display.
Are you getting the code from the start light flashing?

5 flashes should only be shown in the engineer test program.
6 flashes is a water inlet fault.
7 flashes is a flow meter fault

DP

[DentedPorsche]

Re: kenwood dishwasher kid60b12

F5 is listed as “inadequate water supply”.
As it’s filling it would suggest a pressure switch or flow meter fault.
(sorry, haven’t looked to see what’s fitted).

Brian

[DentedPorsche]

Re: De Dietrich DOD438Xu1 Lock

A wiring diagram would be appreciated too.

Thanks

[DentedPorsche]

Re: Zanussi Built-In Oven ZOB550WL Oven Stat – 3 Terminals?

Hiya,
There’s not a lot in this diagram.
Across 1 and 3, it’s the neutral to the fan.
1 and 2, thermostat to the elements (common across the elements).
All the elements are shown to be switched from the selector switch.

If 1 and 3 on the thermostat goes open circuit, the fan should stop.

There are variations of the terminal numbering, P1, 2 and 1 , 1, 2 and 4 etc.

[DentedPorsche]

Re: Zanussi Built-In Oven ZOB550WL Oven Stat – 3 Terminals?

Hiya,
Looks like a switch and thermostat combined. The switch brings on the fan, the thermostat part controls the element (along with the selector switch).

Hope it helps
Brian

[DentedPorsche]

Re: wma31 config

I do, just need your email address to be able to send them to you.
PM sent.
Brian

[DentedPorsche]

Re: Creda T622CW dryer

PM me your email address.
Ta

[DentedPorsche]

Re: Zanussi WJD1257W FAULT CODE

Anything ending in 0 is a customer fault code.
Most likely, if you go into diagnostics, you’ll find the engineer code E11.
Normally caused by the triple valve being faulty.

HTH

[DentedPorsche]

Re: Strix to Diamond H ?????

OK, no problem.

[DentedPorsche]

Re: Strix to Diamond H ?????

OK, the original wiring diagram (which you no doubt have) shows double to 4 and single to 2. you have a double and a single on 2? Where does the double go off to?
I don’t see any hob hot lights so wondering where the extra wires are linked to.

[DentedPorsche]

Re: Strix to Diamond H ?????

I think I’m losing something reading through the thread.
The strix, is it a single regulator having connections P1, 2 and 4 only?

[Author]

Posts