[DentedPorsche]

Re: Tricity Bendix President Double Oven Thermostat R&R

Hiya,
Can you scan and email the instructions you received to me?
Alternatively if you explain what the instructions say I’ll try to work it out with the wiring diagrams.

Thanks
Brian

[DentedPorsche]

Re: Tricity Bendix TM320w Cond dryer

Hiya,
Check the lift pump and the float switch.

HTH
Brian 🙂

[DentedPorsche]

Re: smeg d/washer. drain pump pulsing on/off.

Hiya,
I normally disconnect the dispenser and slave on a washing machine inlet valve, try the machine, if it runs, fit a new dispenser.
Just disconnecting it doesn’t work, it requires a resistance.

HTH
Brian 🙂

[DentedPorsche]

Re: BELLING OVEN GRILL ENERGY REG

Hiya,
Strix stopped making them years ago.
Just use the conversion chart to change to another type of regulator.

HTH
Brian 🙂

[DentedPorsche]

Re: whirlpool awo10761

Hiya,
Have a look at the door, is it sitting centrally in the door recess?
The hinge may have closed up a little moving the door to the right.
Open the hinge a little or trim the plastic in the inner door where the latch rests against to let it spring over a little more.

HTH
Brian 🙂

[DentedPorsche]

Re: LG WM1480 FHD washing machine showing ‘DE’

Hiya,
LE is definitely a lock error on the motor. The hall sensor can’t signal where the motor has parked.

DE is definitely door error

Brian

[DentedPorsche]

Re: LG WM1480 FHD washing machine showing ‘DE’

Hiya,
LE is lock error but refers to the motor, not the door lock. Normally the hall sensor at fault.
DE is a door lock error.
OE is a drain error.

HTH
Brian

[DentedPorsche]

Re: Belling 425 classic

Hiya,
It’s a Diamond H 33ER series, you should be able to get a 44ER series to fit.
Then it’s just a case of rewiring to suit the new switch.

There is a rough guide table of energy regulators in the Diamon H sticky in the forums.

http://www.ukwhitegoods.co.uk/downloads … wiring.pdf

HTH
Brian 🙂

[DentedPorsche]

Re: micromark oven

Hiya,
Can you send the information to me too please?

dentedporsche@hotmail.com

Thanks
Brian 🙂

[DentedPorsche]

Re: Zanussi ZWX1605 error codes

Hiya,
End of cycle is the first number, start/pause the 2nd.
Error E52.

E52: No signal from the motor tachymetric genetaror

If I remember correctly the service manual gives, motor, wiring or pcb.

HTH
Brian 🙂

[DentedPorsche]

Re: Samsung RL33 error codes

Hiya,
Thanks for that.
Appreciate the information.

Thanks
Brian 😀

[DentedPorsche]

Re: cw494/1

Hiya,
The water indicator (black grid in the sump, right hand side) is the normal cause of the problem.

If the appliance actually drains ok then try changing the water indicator.

HTH
Brian 😀

[DentedPorsche]

Re: Caple di604 dishwasher error

Hiya, I’ve got the wiring diagram thanks. Just after the error codes.

Thanks anyway.
Brian

[DentedPorsche]

Re: Hotpoint WMA10P

Hiya,
Stuff on it’s way to your email, sorry they are so big.

Brian 😀

[DentedPorsche]

Re: Bosch WTV74104 Error Codes?

Hiya,
Thanks, got the manuals.

Really appreciate it.
Brian

[Author]

Posts