effzedarr

Forum Replies Created

Viewing 15 posts - 106 through 120 (of 276 total)
  • Author
    Posts
  • in reply to: Zanussi DWS939 D/Wash – Pump Impeller #207700
    effzedarr
    Participant

    Re: Zanussi DWS939 D/Wash – Pump Impeller

    I also seem to remember if the sleeve on the motor shaft is knacked ,it’s a complete motor, might be wrong but something in the back of my mind says i might be right! 😕 😕
    Chris..

    in reply to: WMA31P NO SPIN #208007
    effzedarr
    Participant

    Re: WMA31P NO SPIN

    Never had a probs with repaired boards, you could ask Tony at EMW to test it for you!
    Chris..

    in reply to: Indesit DI620 D/washer #207953
    effzedarr
    Participant

    Re: Indesit DI620 D/washer

    Bad earth on heater? Worth checking had similar on H/point dwf 40.
    Chris..

    in reply to: WMA31P NO SPIN #208004
    effzedarr
    Participant

    Re: WMA31P NO SPIN

    Hi Col, might seem daft to ask but have you run it through the test programme [see error codes etc]? Also is there a load in the m/c ie big towel on it’s own? Could be it carn’t balance the said load! Hope it helps if not i’m sure somebody on this site will put you on the right track!
    Chris..

    in reply to: Radio 2 #207852
    effzedarr
    Participant

    Re: Radio 2

    Thanx for the warning Greg 😀 😀 😀 😀 ❗

    in reply to: Radio 2 #207850
    effzedarr
    Participant

    Re: Radio 2

    Yer right there Greg, Radcliffe hasn’t altered a bit, it’s a same he doesn’t get the gig everytime Wrighty goes on hols, carn’t even remember the name of the last guy they had standing in[such a personality] 😀 😀 :rolls: :rolls: .
    Chris..

    in reply to: Hoover DF967 spray arm #206503
    effzedarr
    Participant

    Re: Hoover DF967 spray arm

    Cheers 916700276 is one of the bits I need ,but also need the bit that actually screws into the spray arm,greyish plastic bit about 1 3/4″ across by 1/2″depth with a few threads on it..
    Regards Chris..

    in reply to: Hoover DF967 spray arm #206502
    effzedarr
    Participant

    Re: Hoover DF967 spray arm

    Thanx guys!

    in reply to: Electrolux oven #206021
    effzedarr
    Participant

    Re: Electrolux oven

    I’ve had a few like this, sometimes it’s the cut-out [microtemp?] in the motor, motor seizing up when warm/hot or cut-out on the cavity or a spade connector to the motor burn’t out [had one of them last month]hope that helps..Chris.

    in reply to: W/pool ADP4404/5 flashes! #205924
    effzedarr
    Participant

    Re: W/pool ADP4404/5 flashes!

    Cheers chaps ,I will order the OWI or WI whatever & give it a go . Just seems odd that it does a pre-wash /rinse ok!
    Chris….

    in reply to: W/pool ADP4404/5 flashes! #205919
    effzedarr
    Participant

    Re: W/pool ADP4404/5 flashes!

    So if it ain’t OWI are we looking at the pcb? Seems drastic at less than 2 yrs old!
    Chris..

    in reply to: virus/spyware #204678
    effzedarr
    Participant

    Re: virus/spyware

    I’ve been using Zonealarm & Symantec Antivirus, so far so good, I hope i haven’t just put the kiss of death on all that 🙁 😥 :rolls:

    in reply to: Hoover HND 315 80 D/Washer….? #204438
    effzedarr
    Participant

    Re: Hoover HND 315 80 D/Washer….?

    Thanx for that Dave, don’t know if customer has gone elswhere [of badly at the mo] also thanx for the e-mail unfortunately my PC isnt letting me open/download any files either, is it on sick with me ? Have we both got a virus? Any body on this site know about PCs?
    regards Chris…

    in reply to: ariston lsi 61 dishwasher #204877
    effzedarr
    Participant

    Re: ariston lsi 61 dishwasher

    I guess these m/cs are similar to the DWF types that HTPT use I would check heater or dispencer, also does the motor still turn over freely when the m/c stops?
    regards Chris…

    in reply to: Hoover HND 315 80 D/Washer….? #204436
    effzedarr
    Participant

    Re: Hoover HND 315 80 D/Washer….?

    Hey guys surely we must have some Hoover engineers on here that can give me some feedback? Please..
    Chris…

Viewing 15 posts - 106 through 120 (of 276 total)