[fasetester]

Re: proline dryer

thanks hello 75 for clearing that up fasetester. 🙂

[fasetester]

Re: bf1620 hotpoint

thanks chris do these suffer from the 3 and one tablet fault. and opening the door during wash over spill. went to check out dishwasher base flooded dryed base seemed to be going ok told the woman to try it for a few days and see how it goes. what are the main points to leak on this dishwasher. thanks fasetester.

[fasetester]

Re: proline dryer

thanks martin for your reply. so if i go to repair one of these and the belt has snapped new bearing kit plus belt or the drum has to be changed as well. which would probably mean scrap. as all that would be the price of a new tumble dryer do the hotpoint creda give the same problum fasetester.

[fasetester]

Re: proline dryer

thanks guys for the reply what would you guys do when you come across this dryer with a broken belt rrrrrrrrun. are the the only dryer that gives this problum even with a new bearing kit the can stil break the belt as you say pen a slightly longer belt a jockey pully cant be fitted as a after kit. do the condencer dryer have this problum. thanks fasetester.

[fasetester]

Re: proline dryer

thanks guys for all your input so it is a waste of time replacing these belts. is there any other dryers that have this problum breaking new belts. the are murder to get round the motor shaft. how come the first belt lasted a year or more. is it when the play comes into the drum that the belt breaks so you need to make sure before you replace the belt that it is going to be a satisfactory repair. fasetester. 🙂

[fasetester]

Re: proline dryer

thanks helo 75 for your reply i went to see it today sure enought the belt had broken again. there is a lot of play and movement in the front of the drum. does the drum jam with the load and the motor shaft burn throught the belt. so if the dryer is pre 06 the bearing kit would make no

differience or would it cure the problum. or the only cure a new drum or dryer when you push the drum back it scrapes on the back panel what tumble dryer would you guys recommend for a fairly big family. thanks fasetester

[fasetester]

Re: proline dryer

thanks brian where is the pic. i dont know if this is the problum i am going to look at it today. as i replaced the belt about six week ago and the woman said it is the same drum not turning the think it is the same thing so you should be repairing it again for no charge thanks fasetester.

[fasetester]

Re: proline dryer

thanks brian for your reply does every kit come with the back and the front bearing. is the front glued on or does it just sit in to the recess some kits just have the bearing plate pin and other ones pop rivets is this a handy job thanks fasetester 🙂

[fasetester]

Re: proline dryer

thanks simonb for your reply does the bearings come as a kit front and back. is the front a felt bearing and have the to be glued on. before i left the had it loaded like a cement mixer and i though i could here it make a scraping sound. does the bearing make for a good repair is there not a mod of a different drum if the bearing have gone would the drum be hard to turn and jam up. thanks fasetester

[fasetester]

Re: Length of manufacturer’s guarantees

thanks ken i should tell the customer before the except the repair that the guarntee is 6 months so the know where the stand fasetester.

[fasetester]

Re: smeg dishwasher DI612c

dave the only give a six months guarntee on the pcb . when i told them i was a engineer and could carry out the repair to the proper standard the said the only give full 12 months to smeg trained engineers. what that all about thanks fasetester.

[fasetester]

Re: Length of manufacturer’s guarantees

thanks ken for your reply should i tell the customer that the only have a six month guarntee what do you guys do fasetester.

[fasetester]

Re: Length of manufacturer’s guarantees

hi guys why will servevast only give a 6 mont guarntee with pcb do the not have to give the full 12 monts fasetester

[fasetester]

Re: Huge potential appliance database?

hi guys most times before i post i will do a search. i will put in the type of appliance make and model no. the forum the category and it bring up all sorts is it not possible just to get the info you want or am i not doing the search right. rhanks fasetester 🙂

[fasetester]

Re: smeg dishwasher DI612c

thanks again for all your help dave i am waiting for servast to reply to my e mail fasetester.

[Author]

Posts