[garn]

Re: hotpoint washers filling and draining as soon as prog st

Just Left One Myself Continuous filling even In The 0 Position On The Selector Switch No Pump Or Motor Action 😥

And The Stones Are Lose Looks Like Volcanic Dust All Over The Pcb 😮

Garn

[garn]

Re: triton shower

Phidom Could be Write.
I had The Same Problem With Mine Recently High Pressure And Freezing Water. Its Been A Bad Winter To And That Elements Been Working Overtime .

I Upgraded From A 8kw To 9.5 kw Its Done The Trick It Is A Pleasure To A hot Shower With Loads of Water Don’t Forget To Up The Fuse t Switch To A Minimum Of 45Amp or 50.

If You Change It Will be Well Worth It I had A Good Deal With Triton Direct.

Paul..

[garn]

Re: SMEG DISH WASHER PART NO

Thanks Lawrence.
Yes It Is RRRRRNing Out The Door 😥

Been Blowing A Bit Of Air Up The P Switch Pipe Had A Couple Of Diferent Reactions After Know It Started to Overfill .

Thanks .Paul

[garn]

Re: HPT new belt fitting tool

wilf wrote:both sides and back off capacitor off (hanging on the wires) drum out. fit belt onto shaft then feed drum into the belt to the side of the machine ensure that the belt is sitting on the line made by the old belt then roll the drum into place over the motor with the belt sitting correctly on the jockey pulley. fit the drum onto the front guides. refit the back then lever the rear of the drum up and into the rear bearing (a screwdriver in a rear perferation leavering against the heat appeture helps)

reassemble

sorted!!!!!!!!!!

wilf 🙂

Thanks Wilf for The Info Thats What Iv Been Doing .
Its A Poor Way These Days

Garn…

[garn]

Re: HPT new belt fitting tool

OK Martin Thanks For The Info
Iv Had no Trouble With The Vented Appliances.
Only With the Condenser Ones The Past Week Managed To Fit to On The job.
I had To Uplift Three In Bits To Take Home To fit Them Then I Had To Have Help 😥
I do Have a Disability To my left Arm But Its Never Been A Problem.

And I Don’t Want To Uplift To Fit A Belt Again Is non Cost Effective

Any Info help I Would Appreciate

Paul…

[garn]

Re: HPT new belt fitting tool

Martin wrote:This is what you want Garn…………….

Part number is: 5600266

HTH? 😀

How The Hec Does That Work Then Martin is There A Demo on U Tube by Any Chance.

paul… 😉

[garn]

Re: scrap prices

What I Found Out A Couple of Years Ago IM About 15 Miles From The Main Scrap Depo its on The Shipping Docks.
When That Ship is Due To Arrive to Take This Scrap to China The Price They Were Paying Went Through The Roof £450.00 A Ton. As Soon As This Ship Left Town The Price Was Back Down To £120 A Ton.

The Quicker They Can Fill This Ship The Less he Pays In Docking Charges Hence The Price Went Up.
so If You can Save It The More You Will Get At The rite time.

Garn

[garn]

Re: scrap prices

Its £125.00 A Ton Down Hear Mixed.

i Load The Drums up With Washing Machine Concrete 😆 Extra£££ 😉

[garn]

Re: Hotpont ctd80 bearing pads

iadom wrote:Four fitted as standard, one extra won’t make much difference.

TA paul

[garn]

Re: bosch washers whats the difference

don wrote:Hi Paul

Right then so you can have a peaceful weekend and a happy mrs 😆 take a look at this comparison link.

The 24164 is discontinued and the 24364 replaces it, however you may still be able to pick up a 24164 which may be cheaper. The spec on both machines is the same.

HTH

Don

Thanks Don Very HandySite to see The Spec
Paul…

[garn]

Re: bosch washers whats the difference

I Noticed tub Bolts From The Front First !/4 Of The tub The Rest Is A 3/4 Rear back Half.

don do you Have Any Idea Between The To Models I Listed On The Start Of This Thread All I can see Is A Price Difference .

The mrs Is On Mmy Back For A New One :rolls:

Paul…

[garn]

Re: bosch washers whats the difference

Thanks jim
Sold A WAA Last Week Had A Peep In The Lid When I Installed It. There Are Tub Bolts There.

My Own Washer Has Just Died And I’m On The Look For Something That Will not Pack in for At Least Seven Years 🙂

Or Am I Asking To Much ❓

Paul… 😉

[garn]

Re: hotpoint TDC32N please Confused

Hi garn hear.

Just Replaced The Door Switch On This One And The On off Button.

The Appliance Seems To Stop At About ten minute in Cycle .
Leave It 1 minute And It Will Restart.
its Not Tripping . Iv also Exchanged The Start Relay.

Can Anyone Point Me In The Rite Direction Please 😳

garn………

[garn]

Re: hotpoint TDC32N part number please

Thanks Mate

The Number I had is MDA1702299

Just Orderd It

Ta paul 😉

[garn]

Re: wheres the work gone?

There Always A Market For Refurbs
Just Look For Large Construction Jobs People Rent Houses And The Landlord has To Supply A Washer Dryer And Cooker.

Take For Instance The Lg gas Pipeline It May be in Your Area All That Mud And All That Washing.

Landlords Are To Tight To Supply A New One So They Will go For A Refurb All Day With A guarantee.
Last Time I Checked It Was In The Southamton Area

There A few Bob To be made There 😉

Garn…

[Author]

Posts