[garn]

Re: Loud Noise AWCT12L Dispenser fill hose rubbing against t

megawatt wrote:Well known and talked about on the ISE forum, worth a look.

Unfortunately no access so i’m over in amica starting from the beginning 🙂

garn…

[garn]

Re: Loud Noise AWCT12L Dispenser fill hose rubbing against t

That’s fare i can see the science I’ll certainly do that Thanks For The tip.

garn

[garn]

Re: What sort of inspection lighting do you use

ring inspection lamp used one for 5years charge it ones a fortnight( http://www.amazon.co.uk/RING-RIL2500-Co … 530&sr=8-1
£29.99 Halfords If You Have a halfords Trade Card Which Is Very Handy Discout Its £22.00.

paul
)

[garn]

Re: Introduction of Iris Codes

does anyone know these iris codes like the back of there hand 😕

1 iv replaced the motor. taco gone defect code Areplaced the module repair code A

struggling with the symptom code A little?

What boils down To It
1st call inspection ” motor taco surging into spin

2Nd replaced motor still the same
3rd call replaced module

What would be the correct iris codes
Defect repair symptom

Thanks paul

[garn]

Re: Had to call the cops today

i had to dump my tools back in the van
walked in the pub and this guy went absolutely bananas on me.
I had a hell of a barney in the bar with him and all these people around 😡
in the end phoned the cops and they came
he told them that this car park is for his customers only.
cops said Do your customers normally drink&drive and he went dead quiet and then he was ordered to let me out.

i was so GOBSMACT that i left and then tel to cansel the job until onother time 🙁 .

[garn]

Re: Orange pocket land line solo service

thanks Butty
Im haveing A think About IT Sounds Good Whats It All Costing A Month Compared To The BT Service

Paul

[garn]

Re: amica AWP 510L MOTOR SURGE

Thanks jim
thought it may be the appliance is still under guarantee il have to book in after the new year.

are you able to change the taco on these or is it a replacement motor

ta Paul..blwythyn newith tha

[garn]

Re: Daewoo appliances warranty ?

Steve said

One customer refused repair and has had an exchange and purchased a different brand!

Hope not A customer Refused a 2nd repair On a Amica I exchanged a Amica For a daewoo 🙁

garn

[garn]

Re: Daewoo appliances warranty ?

Got A Couple of units in tomorrow i asked who covering the repairs I was told the boys ukwg are covering it.

had a look on line and Guarantee is registered with home serve. (http://www.daewooelectronics.co.uk/daew … antee.aspx )

[garn]

Re: Welcome back penguin45

welcome back as-well Chris. 😉

missed you as a referee in hear you stopped a lot of scraps
your the only one who came to my defence when i made some
sbelling mistakes or twyping mistakse 😀

paul..

[garn]

Re: HOOVER HNC 382T I need A lesson Please

loopey wrote:Please tell me why you have disconnected all the front pcb relay extra . no need to do this at all simple waste of time ?
it was pulled lose to inspect because it was tight when i was lifting the drum upwards to remove yes it was my first strip-down with this model but i didn’t break or crack any plasticscosting my business ££.££ or retuning the appliance with the plastics glued up and not informing the customer i messed it. or even informing them it was BER because i broke it.

I am glad you not my engineer 6 hours turn a round in a work shop . wow

As for working for anyone i am personally registered green card worker ( Disability’s ) you mention that to an employer and nobody wants to know they say in a polite way.I Have superb skills all my life and been self employed all my life i ain’t going to any employer to be exploited to there full potential.
Waveing a stick at me because he wants ten or fifteen jobs completed a day.

one Completed job no damage £90.00 payment and the customer is happy.

paul…

no disrepect in any way …

(edit) any spelling mistakes are due to being dislexic , this a true fact , ask any one that might no me lol

need any help just ask regards phil poole 🙂

[garn]

Re: GENERIAL DOMESTC APPLIANCES DISHWASHER. MODEL BF41

thanks butty and its in stock its identical to C00211045.
il take a punt on this one and order it .

garn.

[garn]

Re: HOOVER HNC 382T I need A lesson Please

ITS taken me 2.5 hrs to strip it last night
and three shots through the day back&foe an hour each time to rebuild it and test it this evening.

just about six Hours By The time I take It back :rolls:
Dont think il fancy striping one of these down on A call.

GARN

[garn]

Re: Having an affair.

I thought you were bulling 😆

i wasn’t 😆

garn

[garn]

Re: HOOVER HNC 382T I need A lesson Please

Iv Just Had it lose Thanks i really appreciate the push forward i didn’t have the strength to pull the front up so i used 2 flat screwdrivers on the bottom holders like bob said and prized forward and up individually.

Thanks i though i was going to break it was tight

[Author]

Posts