Geoff1312

Forum Replies Created

Viewing 11 posts - 31 through 41 (of 41 total)
1 2 3
  • Author
    Posts
  • June 16, 2010 at 8:47 am in reply to: Hotpoint (Indesit )DI450 Module #322435
    Geoff1312
    Participant

    Re: Hotpoint DI450 Module

    Hi Iadom,

    Thanks for that. It’s not C00143214 as I had one of these and tried it. Is it possible you can give me part numbers for the other two? I will go back and check serial number.

    Thanks
    Geoff

    March 3, 2009 at 6:14 pm in reply to: Neff wash pump running slow S5943X0GB/08 #275058
    Geoff1312
    Participant

    Re: Neff wash pump running slow S5943X0GB/08

    Hi All,
    Finally resolved problem. Customer took along time to decide on repair, fitted new wash pump + sealing kit. All working fine.

    Thanks for your help
    Geoff

    January 23, 2009 at 4:43 pm in reply to: Neff wash pump running slow S5943X0GB/08 #275053
    Geoff1312
    Participant

    Re: Neff wash pump running slow S5943X0GB/08

    Thanks for your reply Martin.

    Wash pump rotor turns easily and starts turning as soon as powered up. Hence assume capacitor ok. Can hear from lack of noise and see with side panel off that pump doesn’t reach full speed, thus not activating heater and very weak wash action.

    Must admit haven’t tried replacement capacitor. Do you think I should?

    Thanks
    Geoff

    November 19, 2008 at 4:36 pm in reply to: Hotpoint TDL60 #268762
    Geoff1312
    Participant

    Re: Hotpoint TDL60

    On deeper inspection everything pointed to selector switch. As none in stock at connections, decided to dismantle switch. Cleaned and reassembled, refitted and turned on hey presto! it worked 😀

    Thanks gents once more for your assistance
    Geoff

    November 17, 2008 at 6:02 pm in reply to: Hotpoint TDL60 #268760
    Geoff1312
    Participant

    Re: Hotpoint TDL60

    Thanks Martin, Tested door switch ok, front stat ok. With door open clean filter light illuminates. Any more ideas please?

    August 1, 2008 at 3:31 pm in reply to: Ariston LSI61 #258359
    Geoff1312
    Participant

    Re: Ariston LSI61

    After getting over the shock of the machine still not working after replacing the PCB I scanned previous posts on this machine. Returned to machine checked element, insulation down. Replaced element, machine now working like a dream.

    God bless UK Whitegoods forum and all you gentleman who contribute to it.

    Regards
    A now happy Geoff 😆

    April 10, 2008 at 10:33 am in reply to: Hotpoint RLA34P #248519
    Geoff1312
    Participant

    Re: Hotpoint RLA34P

    Door seals ok , light goes off . This hasn’t got exposed evaporator the stat capillary goes down a tube within the insulation and goes in fairly easily to the same depth as original . Any more suggestions please .
    Thanks for all help so far .
    Geoff.

    January 9, 2008 at 4:43 pm in reply to: Bosch SGS53C02GB/08 Fault #239127
    Geoff1312
    Participant

    Re: Bosch SGS53C02GB/08 Fault

    Hi Graham

    Not totally conversant with this machine, but have had a similar problem with some Bosch dishwashers where the transfer pipe that goes across the front of the machine from water inlet tank on l/h side to machine sump is blocked. And float switch detects an overfill situation and brings the pump on.

    Good luck

    Geoff

    January 9, 2008 at 4:35 pm in reply to: Beko WMA1715S Pre wash light flashes #238952
    Geoff1312
    Participant

    Re: Beko WMA1715S Pre wash light flashes

    Thanks Gentlemen,
    Your expert help worked. Flashing pre wash light does mean the child lock is on. Customer obviously unknowingly set it whilst trying to clear fault lights.

    You have saved another Beko machine from the scrap heap.

    Thanks again, what an excellent site this is!
    Geoff 😀 😀 😀

    October 8, 2007 at 3:56 pm in reply to: Hoover HP13-80 help #228538
    Geoff1312
    Participant

    Re: Hoover HP13-80 help

    Sorry for delay in reply, customer on holiday. Thanks for replies, sadly the pump was ok. Must require PCB as advised. This is a special order from Connect, customer not prepared to wait any longer. Purchased new machine from us needless to say not a Hoover! Hoovers loss.

    Thanks again
    Geoff

    June 25, 2007 at 1:20 pm in reply to: fault codes pdf #212267
    Geoff1312
    Participant

    Re: fault codes pdf

    Hello,
    Please could I have a copy too
    sdas@binfield.wanadoo.co.uk
    Cheers
    Geoff

  • Author
    Posts
Viewing 11 posts - 31 through 41 (of 41 total)
1 2 3