Forum Replies Created
-
Posts
-
Re: Hoover washer dryer wdyns654 – please help!!!
ok, best thing to try
press and hold the night and day button, turn the machine on, hold for 8 seconds (every icon will be on), then let go and within 2 seconds, press start… the machine should start and do a test programme….
it should revert to normal 1 minute after its spin
good luck
Re: Faulty Servis M3102A
its worth checking the brushes in the motor
other than that its likely to pcb fault, and be ber for sure
Re: Hotpoint WD860 – f-013 error
Its more likely to be blocked full of fluff or the fans faultered/blocked/fell off and tripped the thermal fuse
u really need unplug it, strip the heater box and have a look tbh.. it may be repairable with no parts, but it might, need to look really
hope this helps
Re: Overheating Candy GO F462-80
2babecom wrote:yes i sprayed the bloody switch which is attatched to the pcb circuit board.
The correct part was ordered actually as all the part numbers matched now if you have no help to give why dont you get off this thread and go annoy someone else!!!!!!!!
ok, you asked, youll get your answer,
the pcb you ordered is the right one, it just isnt programmedthe spraying of the switch works rather well, i do it daily
now you either pay for the right, programmed pcb, or you pay a hoover/candy engineer to programme the one you have
the advice is here, you just didnt take it
Re: Overheating Candy GO F462-80
does no1 do any research?
take the knob off and spray the selector with switch cleaner
job doneRe: WMD960 – F01 etc
no brushes im afraid, its a 3 phase motor
i found many of those to have a loose/broken wire in the motor plug, however i found many more with pcb failure
check the motor connections, if theyre not broken, it will need a pcb, theres no inbetween im sorry
Re: BUSH WM-1260B AUTOMATIC WASHER
we have a troll
at no points did i ‘kinda guess’ anything
nor was any of my post badly worded or punctuatedjust like i didnt use offensive or nasty words
wont be long before this thread is locked, removed or you get a ban
freedom of speech is brilliant untill you abuse it
ill say no more, i think your previous 2 posts speak volumes, whether you consider me impertimemt or not
Re: Haier Bearing Change
out the top mate
bearings are around 50p each and the seal around 20p
good luck though, its worth more to weigh it in, and a lot less hassle
Re: BUSH WM-1260B AUTOMATIC WASHER
judging by the wording of your posts im guessing youre either poorly educated or your not from these here parts
im kinda guessing that you actually work for haier? im going to be quite frank here, im known for it, and im sure other traders will agree
bush/haier/swan/russell hobbs/matsui/hec/whatever they think of next
are simply inferior products
the beauty of internet forums is that anyone, anywhere can post these kind of messages, theyre easy to post, and most probably, are made up to enhance the brands selling point
traders know, the fire brigade know, trading standards know
from poor, badly built motors, to naff pumps, pcbs that wont spin… wierd electrical faults and motors that spontaneously combust, the problems seem continuous
in fact the only saving grace is that when the motor sets on fire , it manages to melt the tub and it puts the fire out when it pours water out
great safetey feature i dont think
people need to get to grips with the fact that not only are they rubbish, theyre destroying our economy, taking peoples jobs and creating serious safety issuesif u really have had your machine 2 years, then good luck to you
Re: Bit of advice RE – COMET
and thats an end to that
they sent me a list of my so called holidays, and after checking them with my previous fuel returns, they where well out
so id like to thank comet for putting £154 in my bank account on the 25th, im glad you wasted money on bailiffs and letters, cost you a lot of money…
what a poorly run, awful company they are
roll on the day the shutters go down for the last time
Re: Candy GO F662 erratic behavious
washing-machine-forum/hoover-wmh-147-timer-problem-t72321.html
same machine, same problem
Re: Hoover HD Vison
just make sure its unplugged, take off the back, and its there , just above the motor,a bit to the right… its not a bad job as long as the nut is slackend and the seal is loosened off
good luck
Re: Hoover HD Vison
washing-machine-forum/hoover-vision-1200-timesaver-mode-t64650.html
