Forum Replies Created
-
Posts
-
Re: Anguis in herba
Spoilsport, 🙂 I was just going to post a link to a new Bosch D/W to see if he would take the hint. Daves approach is perhaps for the best. 8)
Re: Anguis in herba
He appears to have drawn Turbo into his web ATM, I would love to sit back and see how their relationship evolves. 😆
Re: new FEW 12
Turbo wrote:.
Would be nice to see a write up in the Independent one dayor even better in a quality paper that far more people read 😉
Its not the wishy washy liberals we need to educate. 😆
Re: Hotpoint Aquarius Noisy on Spin – Any help please!
If she cannot find her details, give us the serial number from the door hinge and we should be able to date it, we can tell month of manufacture and if it is under 5 years old she should be OK.
Re: Anguis in herba
Penguin45 wrote:I dealt with it….. only a tinge of sarcasm…….
looks like your sarcasm backfired Chris. 😆Blue tubes, you saw me standing alone
I think we should set gegsy on him again, I wonder if justin is a Barca supporter. 😆
Re: World Cup 2006
Oops. A bit premature what. 😀
What goes beep, beep, beep, beep..
The A5senal open topped bus reversing back into the garage 😆
Re: Anguis in herba
I thought the same when I read them last night, I wonder if his next request will be for a friend of a friend. 🙂
Re: Doing jobs for friends…..a no no!!!!
cornwell40 wrote:
So after a few minutes investigation and head scratching I started looking at the new motor, and there it was!! Instead of fitting the new plug to the loom, the clown who replaced it had shaved off the locating guides on the old plug.That was almost standard practice for Hotpoint engineers, it works perfectly and never causes problems, unless you remove it then refit it without taking note of its original position. 😥
I’ll bet you check the next one. 😉
As they say,” a friend in need is a pain in the butt”.
Re: Anguis in herba
OMG, justins back. 😥 🙂
Re: Hotpoint Electronic 800 Delux 9526 – not cleaning
Glad to hear that, thanks for coming back to us with the results. :tup:
Jim.
Re: An offer you can’t refuse?
A good friend of mine has voted against and returned his form, funny thing is, he retired 5 months ago. 😆
Re: Hotpoint E15 error
A CD 😯
Thanks for letting us know the outcome. :tup:A pump blockage should not cause out of balance, loud banging or trip the electrics.
keep a close eye on the machine for next few washes.Re: Hotpoint BFI680 Fault Code
Hi Ade. I have copied your second post on this machine into this post and will delete it.
Ade1 said, quote,
I’ve replaced the heater, but am now getting flashing button 4 (auto eco). Hotpoint advise it means “time out on heating check thermistor positioning on dispenser”. Can anyone tell me what I do now, before I finally have to call in the engineer? Many Thanks.It helps to keep things tidy and means that if anyone replies to your original thread you will get a notification.
Neon 4 flashing may mean the base is flooded. When you replaced heater how did you refix the hoses. The original clips are almost impossible to refit, you may have a leak from your handywork.
With the machine unplugged tilt it backwards or to one side, if water runs out then you have flooded the base.
If there is no water then it may be time for the experts. 😉
Re: Hotpoint Aquarius – Conditioner problems
This can be caused by using a conditioner that is to thick, poor water pressure or sometimes by careless filling of the soap powder, ie pouring it in and getting some into the fabric conditioner compartment. Also depending on which model you have ( you didn’t say) 😉 you may have the drawer set for liquids whilst using powders. This can cause the powder to splash over into the conditioner compartment and will block it very quickly.
If the type of conditioner you use is on the thick side then water it down a little before use or switch to a different brand that is more fluid.
