iadom

Forum Replies Created

Viewing 15 posts - 3,256 through 3,270 (of 25,656 total)
  • Author
    Posts
  • in reply to: indesit widl126s washer dryer #428316
    iadom
    Moderator

    Re: indesit widl126s washer dryer

    Dryer ntc can cause all sorts of weird faults on these. Either of the elements down to earth?

    in reply to: Neff error code? #428287
    iadom
    Moderator

    Re: Neff error code?

    Thanks Paul, at least that confirms Martins thoughts.

    A bit of a strange customer TBH, rang last weekend, call was booked for Tuesday but I had a cancellation for Monday and rang the number he left five or six times over the weekend and Monday, during the day and in the evening but got the answerphone every time. Late on Monday night I got a message that he had now sorted it and not to bother. He called back Tuesday evening to say it had stuck again.

    Called yesterday and he gave me a mobile number instead. Rang that several times yesterday and night without getting an answer, rang the landline but got answerphone every time. I eventually sent him a text message asking him to ring me and got a reply from him this morning saying that he had once again ‘fixed’ it.

    I’m guessing that it is drying up just enough to allow the door to open before it leaks again.

    I await his next call. :rolls:

    in reply to: In search of the fourth cord #284839
    iadom
    Moderator

    Re: In search of the fourth cord

    I really have no idea what I am supposed to have said or done to provoke
    THIS tone of post from timdowning????

    in reply to: Neff error code? #428284
    iadom
    Moderator

    Re: Neff error code?

    timdowning wrote:Don’t go blaming BG what have they done to hurt you?

    .

    Nothing to ‘hurt’ me personally but I have seen many instances of their work in this area over the years and it didn’t inspire confidence in a lot of cases. 🙁

    I am however at a complete loss as to the reasons for what I perceive to be a hint of thinly disguised sarcasm in your posts, I have no idea what I have done to hurt you?

    in reply to: Neff error code? #428281
    iadom
    Moderator

    Re: Neff error code?

    Not clever enough by half, 🙁 don’t see that many of these and not had one with the door locked before, never to old to learn. 🙂

    Although TBH there was no sign of the red door release, suspect it might have been ripped off at some time, apparently had several major repairs done by BG.

    Thanks for your replies. 8)

    in reply to: Indesit IWDC6125 #428274
    iadom
    Moderator

    Re: Indesit IWDC6125

    Error codes HERE

    You do not ignore the bottom light, the vertical lights do not flash, only the horizontal lights flash.

    in reply to: hotpoint lft114 #428237
    iadom
    Moderator

    Re: hotpoint lft114

    Four different models of LFT114 and at least two different control cards, full model number and suffix or commercial code needed to ID. Card is around £31 list price though.

    in reply to: ISE 555 was ok , So i thought! #428254
    iadom
    Moderator

    Re: ISE 555 was ok , So i thought!

    You should always fit a new drum seal.

    in reply to: ISE 555 was ok , So i thought! #428252
    iadom
    Moderator

    Re: ISE 555 was ok , So i thought!

    Yes, give it a couple of hard clouts with a big hammer to break the loctite seal taking care not to damage it.

    PS, That’s the drum pulley, the ‘spider’ is inside. 😉

    in reply to: C00224176 – ToC for Creda built under #428240
    iadom
    Moderator

    Re: C00224176 – ToC for Creda built under

    Unfortunately I don’t have a manual/wiring diagram for that model, not sure if anyone else may have one.

    in reply to: C00224176 – ToC for Creda built under #428238
    iadom
    Moderator

    Re: C00224176 – ToC for Creda built under

    A model number would be a good idea. 😉

    in reply to: hotpoint lft114 #428235
    iadom
    Moderator

    Re: hotpoint lft114

    Stuck buttons, faulty led card ?????

    in reply to: Hotpoint WDL540 Washer Dryer Not drying properly #428230
    iadom
    Moderator

    Re: Hotpoint WDL540 Washer Dryer Not drying properly

    Depends if it is a sealed or screwed drum, integral on the screwed drum, separate condenser on welded drum. Need full model number and commercial code to be sure.

    in reply to: What is this part? #428227
    iadom
    Moderator

    Re: What is this part?

    Bear in mind that E40 is only the user facing error code, there are actually 6 or 7 ‘E40’ codes. running the diagnostics is the only way to be certain, not always the door lock itself.

    in reply to: WIB 111 stuck #428151
    iadom
    Moderator

    Re: WIB 111 stuck

    Part number is C00273898, usually sold as a single item for some daft reason, you need two.

Viewing 15 posts - 3,256 through 3,270 (of 25,656 total)