Forum Replies Created
-
Posts
-
Re: ISE10 1606W bearings
100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} bearings failing. 🙁
Re: ISE10 1606W bearings
Something obviously wrong but difficult to say what it could be from that.
If you take the belt off and then spin the drum as fast as you can through the door it should be absolutely silent, no noise of any kind.
If you can hear anything at all with the belt off it would point to bearings.
Bearings themselves don’t fail initially, it is the water seal that fails allowing detergent and water into the bearings.Re: ISE10 1606W bearings
Loose weights on ISE 10, doesn’t happen.
Suspension faults also very, very rare. I have only ever changed one single rear suspension leg due to a leak from above.
Foreign bodies, large coins etc inside the outer drum a possibility, you can easily remove one of the drum lifters to check for this and examine the heating element at the same time. I have had one heating element that was loose and the machine sounded like an automatic rifle on full spin.
Details of how to remove the drum lifters is in the user manual.
Re: Bosch heatpumps failing on install,is it just me??
electrofix wrote:
if these units were ultra unreliable I think Bosch Neff engineers would be going hairless with Under guarantee repairs
Rumoured that sales of decent ‘syrups’ ( cockney rhyming slang) are at an all time high amongst their ranks.TBH it won’t really worry them, it’s the Indies who fit them out of warranty who will be suffering. 🙁
Re: Brand new Hotpoint BHWD129 washer and dryer strange nois
The water feed into the condenser is normally a steady trickle, never heard one make that noise. Certainly nothing to do with being unlevel.
I would get Hotpoint to check it out.
This machine is basically a bog standard 10 year old design from Indesit, no obvious changes to the internals on the dryer side as far as I can see.
Re: Hotpoint TD WSF 83EPZ/ Error F03
Not seen one either, looks like a Whirlpool job.
Not sure if the ntc shown on the fan cowling is the one you need.
Jim.
Re: Hotpoint Aquarius very noisy on spin, have a listen!
tonyrobbo wrote:
Also why has it come loose, could there be another fault that has caused this?Because it is basically a cheapo Indesit under the skin. 🙁
How old is the machine?
Re: Hotpoint Aquarius very noisy on spin, have a listen!
Full wrap round cabinet on this machine. so everything has to be lifted out through the top. 🙁
99{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} of the time the mounting mouldings on the drum front are too badly damaged or ripped off completely.
Peel back the door seal to check and look up underneath as well.Drum assembly is around £160 and the earlier drum is no longer available. If you have the earlier drum assembly then it would also need a new condenser to fit with the new drum. Full serial number needed to identify which drum yours has.
Re: Button bank for whirlpool model no 851700901000 please
Doesn’t appear to be listed as a separate part, just control panel.
C00379920.
Re: Dryer Hotpoint states Tvfs83cgp Uk
That thermoSTAT kit is the correct one, see attached diagram.
Jim.
Re: replacing diamond h 33erx22m with ego 5055073010
Moved to Trade Tech, originally posted in Public Forums. 😉
Re: First 4 Service
expertcat wrote:Suppressed no one has mentioned they have gone into administration
.???
The second paragraph in Ken’s post above states exactly that. 😉
Re: AEG lavamat Turbo protex not drying
Can you run the diagnostics routine.
With one finger switch the machine on and hold, then press the start/pause button and the next option button to the left, hold all three for about three seconds until the display starts scrolling through.
Turn the control knob one click at a time until you get an error message displayed. There are around fifty of them, all begin with E.
NB. You don’t mention checking the elements for insulation leaks to earth, a very common cause of strange faults on Zanussi washer dryers.
