johnmac11

Forum Replies Created

Viewing 15 posts - 496 through 510 (of 1,760 total)
  • Author
    Posts
  • in reply to: Whirlpool ADP4500 #356748
    johnmac11
    Participant

    Re: Whirlpool ADP4500

    Spooky…. :eeek: had the same problem with the same model today.
    when you switch the machine on and press the start button it should pump out before filling. What is happening is the pump goes and the program and start led’s go on and off every second in time with the pump.

    I have had a few of these and it is usualy a faulty bottom pcb.

    John

    in reply to: Neff T1281no/02 #356660
    johnmac11
    Participant

    Re: Neff T1281no/02

    The part number is 297234

    John

    in reply to: Fisher & Paykel DD603H #356594
    johnmac11
    Participant

    Re: Fisher & Paykel DD603H

    Dont see how you could have fitted it wrongly, if it was in wrong it would leak everywhere.

    It is not often that they fail this quick but I have come across it before. PM me your email address and I will send you some info that will help.

    John

    in reply to: Fisher & Paykel DD603H #356592
    johnmac11
    Participant

    Re: Fisher & Paykel DD603H

    If one drawer is dead is usually the heater plate open circuit.

    John

    in reply to: Whirlpool AWM5125/? worth doing bearings? #356447
    johnmac11
    Participant

    Re: Whirlpool AWM5125/? worth doing bearings?

    Easy job Mike, should take about 45 mins.

    John

    in reply to: whirlpool dryer #356483
    johnmac11
    Participant

    Re: whirlpool dryer

    Hi Paul,

    Manual sent by email

    HTH


    John

    in reply to: whirlpool dryer #356481
    johnmac11
    Participant

    Re: whirlpool dryer

    Which model??

    John

    in reply to: Most expensive repairs. #356464
    johnmac11
    Participant

    Re: Most expensive repairs.

    I put two doors on a Whirlpool side by side for Saga insurance about 8 years ago. The fridge was 6 months old and the customer stumbled into it and damaged both doors.

    Total invoice £1150 :eeek:

    John

    in reply to: Whirlpool AWM5125/? worth doing bearings? #356445
    johnmac11
    Participant

    Re: Whirlpool AWM5125/? worth doing bearings?

    Hi Mike,

    Just stick a large flat bladed screwdriver behind each clip and force them off, when rebuilding, line each clip up and tap with a hammer and they will go back on quite easily.

    John

    in reply to: schreiber app6302 #356069
    johnmac11
    Participant

    Re: schreiber app6302

    Fridge door is available HERE in the UK Whitegoods shop.

    HTH

    John

    in reply to: Whirlpool D/W pump #356064
    johnmac11
    Participant

    Re: Whirlpool D/W pump

    Wash pump for that one is 481236158336 and it is superceded by 481236158428, get your wallet out Jim 😆

    John

    in reply to: cda cd251ss #355969
    johnmac11
    Participant

    Re: cda cd251ss

    Part number is 040199009963R and direct from CDA will probably be your best bet.


    John

    in reply to: “Ooooh Matron” ? #165874
    johnmac11
    Participant

    Re:

    Does that mean they will have loads of little Miele’s coming soon…. :rotfl:

    John

    in reply to: whirlpool heater #355809
    johnmac11
    Participant

    Re: whirlpool heater

    That number is correct for that 12nc

    John

    in reply to: Beko fridge freeze recall #354793
    johnmac11
    Participant

    Re: Beko fridge freeze recall

    Hi Ally,

    Beko say that the one I have is not covered under the recall but does need the defrost kit. Part in stock at http://www.beko-spares.co.uk/ £12 + postage

    John

Viewing 15 posts - 496 through 510 (of 1,760 total)