Kirk

Forum Replies Created

Viewing 15 posts - 166 through 180 (of 250 total)
1 2 3 … 11 12 13 … 15 16 17
  • Author
    Posts
  • March 9, 2006 at 8:00 pm in reply to: Expert / Glen Dimplex #161518
    Kirk
    Participant

    Re: Expert / Glen Dimplex

    Now that expert has gone Stoves are now going to use their own engineers on LEC but not on systems yet, so who is going to do that NESN?

    Kirk

    March 2, 2006 at 8:16 pm in reply to: The Big Bad Wolf #167081
    Kirk
    Participant

    Re: The Big Bad Wolf

    I am told that EAC is offering its eng stock and vans at a knock down price at the end of the month? are they going to be offered work direct as well, if so they will not be offered good terms.

    Kirk

    February 22, 2006 at 9:28 pm in reply to: Samsung RS21 WCSV #166423
    Kirk
    Participant

    Re: Samsung RS21 WCSV

    Thanks Dave & Flyman

    February 19, 2006 at 7:49 pm in reply to: Zanussi IZ161W Fault? #166176
    Kirk
    Participant

    Re: Zanussi IZ161W Fault?

    Thanks Dave got it but it still does not tell me if I’am correct or not
    small print explaining it adjusts itself, but customer wont believe it.

    Kirk

    February 19, 2006 at 4:03 pm in reply to: Zanussi IZ161W Fault? #166174
    Kirk
    Participant

    Re: Zanussi IZ161W Fault?

    Thanks Martin for the quick reply but I can’t find this one.

    IZ161W 40501504 / 91451309700

    Thanks Kirk

    February 6, 2006 at 3:45 pm in reply to: Hotpoint WF320P #163570
    Kirk
    Participant

    Re: Hotpoint WF320P

    Thanks Dave it mentioned eprom so I thought Indesit..

    Norman

    January 23, 2006 at 5:42 pm in reply to: Brandt D/W Hinges #161883
    Kirk
    Participant

    Re: Brandt D/W Hinges

    Thanks Dave on the ball as usual.

    Norman

    January 9, 2006 at 12:07 am in reply to: lg direct drive bearing change #160219
    Kirk
    Participant

    Re: lg direct drive bearing change

    Once you have undone the bolts it just falls off just be careful with the plug connectors.

    Kirk

    January 4, 2006 at 9:52 pm in reply to: LGwm1260 FHD #159778
    Kirk
    Participant

    Re: LGwm1260 FHD

    Yes Mark,
    I agree with bob it is quicker than Zanussi and about the same as WMA, you can do just bearings and seal or rear half tub, bearings are dearer than Zanussi.

    The direct drive motor pulley off and the 6 bolts that hold the rotor on not the ones that go round the metal back plate.

    Kirk

    December 5, 2005 at 5:50 pm in reply to: Smeg D/W Fault codes? #156871
    Kirk
    Participant

    Re: Smeg D/W Fault codes?

    It is a DWF64SSE

    December 5, 2005 at 5:27 pm in reply to: Smeg D/W Fault codes? #156869
    Kirk
    Participant

    Re: Smeg D/W Fault codes? Model dwf64sse

    Sorry this is the model no. of the smeg dw with flashing lights. Thank you.

    December 4, 2005 at 9:45 pm in reply to: Too cold Fridgemaster fridge MTRL130 #156647
    Kirk
    Participant

    Re: Too cold Fridgemaster fridge MTRL130

    This model had a problem with the defrost cycle not defrosting all the ice, so slowly building up above the drain hole and eventually covering it, usually the water leaks onto the bottom of the fridge then the floor if this hasn’t happened it is probably the stat.

    Kirk

    December 4, 2005 at 5:39 pm in reply to: Too cold Fridgemaster fridge MTRL130 #156645
    Kirk
    Participant

    Re: Too cold Fridgemaster fridge MTRL130

    It could be a simple T Stat fault but first, I would check that there is a big build up of ice on the back wall all over the upper part, if it is only half down and lower half is clear it will be the stat. If it comes down to the defrost hole it could have a more seirous problem.

    Kirk

    November 25, 2005 at 10:22 pm in reply to: Fridge Freezer Cold Location #155560
    Kirk
    Participant

    Re: Fridge Freezer Cold Location

    Lots of engineers have the knowledge but don’t have the time for an in debt arguement with people that have no knowledge, I use to carry a print out to hand to them.

    We also many years ago fitted a heater in some to overcome this which was the second best solution.

    Kirk

    November 25, 2005 at 10:15 pm in reply to: Indi???? #155590
    Kirk
    Participant

    Re: Indi????

    The bearings seem fine so I assume that it is the tub that is the problem, and that some of you will have worked out magic repairs, both eng’s checked the suspension due to LG experiance both felt it was the tub so is it a complete assembly?

    I have kevlar gloves and arm protectors but nothing for the temper involved.

    I have done two plastic tub changes when I was offered work before but thought I would leave it to people that are kind stress free have all the FREE time in the world.

    Kirk

  • Author
    Posts
Viewing 15 posts - 166 through 180 (of 250 total)
1 2 3 … 11 12 13 … 15 16 17