Kirk

Forum Replies Created

Viewing 15 posts - 151 through 165 (of 250 total)
1 2 3 … 10 11 12 … 15 16 17
  • Author
    Posts
  • July 4, 2006 at 8:37 pm in reply to: Subscribers spares deals #114407
    Kirk
    Participant

    Re: Subscribers spares deals

    Sorry Dave I don’t think it will work, as you have seen by the amount of subscribers very few are interested in anything bar their own selve’s.

    The chance of them bulk buying is negligible with next day delivery it was different a few years ago when the vans came round once a fortnight.

    I had a job lot of Servis modules and was selling new at half the price of EMW recons, sold about 20, had been trying to sell in boxes of 20 didn’t sell one box and they were all current ones.

    I have always bought bulk but it doesn’t pay now.

    Kirk

    June 29, 2006 at 9:06 pm in reply to: Zanussi Condensor Dryer TCE 7276W 91609266701 #180475
    Kirk
    Participant

    Re: Zanussi Condensor Dryer TCE 7276W 91609266701

    Part is a Diffuser Lumiious DST1251185300 £3.??

    Kirk

    June 29, 2006 at 8:57 pm in reply to: Danfoss electronic stater? #180362
    Kirk
    Participant

    Re: Danfoss electronic stater?

    Thanks saw the fuse but haven’t checked it yet was curious to know why it was so involved.

    Thanks again Kirk

    June 29, 2006 at 5:06 pm in reply to: Danfoss electronic stater? #180360
    Kirk
    Participant

    Re: Danfoss electronic stater?

    Sorry Dave nothing like that I have used that type 25+ years.

    This one fits on the side of Danfoss pot is about 6 inches square 2 inches thick has a great big alloy heat sink on it and loads of electronics in it.

    I can only see it as a starter as there is no wiring going back to anything

    Thanks again Kirk

    June 13, 2006 at 8:26 pm in reply to: LG wm1480fhg LE fault motor! #179121
    Kirk
    Participant

    Re: LG wm1480fhg LE fault motor!

    Every one I have had with that fault has been the motor.

    Kirk

    June 12, 2006 at 9:04 pm in reply to: Admiral Top Loader AW22 #179020
    Kirk
    Participant

    Re: Admiral Top Loader AW22

    Thanks for the reply I could not see how motor worked as it was in a very difficult place and thought I would get advice first, I did try it on spin with no load but of course very quite, the customer is adamant that it is the drum, and when you push it over it stays there not like the old Hotpoints but all the springs seem ok, this appliance is two years old.

    Thanks Kirk

    May 24, 2006 at 9:56 pm in reply to: Zanussi T/D not drying TC470 #177329
    Kirk
    Participant

    Re: Zanussi T/D not drying TC470

    Thanks for your input it made we look properly at the fan and found it was jamming up and running slow.

    Kirk

    May 23, 2006 at 11:38 am in reply to: Zanussi T/D not drying TC470 #177327
    Kirk
    Participant

    Re: Zanussi T/D not drying TC470

    Hi you two Guys… thanks for the info, will let you know how I get on…

    Kirk

    😀 8) 🙂 8)

    May 19, 2006 at 6:20 pm in reply to: Delonghi DFS 901 SS #177040
    Kirk
    Participant

    Re: Delonghi DFS 901 SS

    I have done dozens of these conversions and it is really easy, you can buy the switch on its own but the load still then comes through the switch, on the conversion it is diverted so no more problems, in days when I just changed switch some would only last a few weeks.

    Kirk

    May 4, 2006 at 7:41 pm in reply to: Belling ID602/2 How do you reset it #175315
    Kirk
    Participant

    Re: Belling ID602/2 How do you reset it

    Thanks Dave sorted Norman

    May 1, 2006 at 7:35 pm in reply to: Comin through !! #174570
    Kirk
    Participant

    Re: Comin through !!

    Now Agro works for himself he is out every morning 5.30 polishing it, at least Lawrence’s van you could see a sort of colour.

    Kirk

    April 30, 2006 at 6:27 pm in reply to: Smeg DWF64sse Dead #174534
    Kirk
    Participant

    Re: Smeg DWF64sse Dead

    Thanks for your help didn’t check that. Kirk

    April 4, 2006 at 9:06 pm in reply to: Zanussi F/F – Mod – ZX56/4 W #172115
    Kirk
    Participant

    Re: Zanussi F/F – Mod – ZX56/4 W

    The most common fault is in the freezer if both defrost heaters have been working, it is usually the main one that fails or the timer. at the bottom of the evap at the back are three vent holes for cold air up to fridge if the customer did not leave off long enough it needs 24 hours door open or a steamer to clear them. Steamer takes about 5 mins. If this blocks in two weeks the defrost is not working
    Stat I don’t use the VT9 in this unit only Zan 2262199116.

    Kirk

    April 4, 2006 at 7:31 pm in reply to: Hoover SE160E PCB #172102
    Kirk
    Participant

    Re: Hoover SE160E PCB

    Thanks for the info also sorry for two posts but hadn’t given you full model number.

    Kirk

    April 4, 2006 at 8:52 am in reply to: Belling ID602 DW Pump? #172008
    Kirk
    Participant

    Re: Belling ID602/2 DW Pump?

    Thanks both of you but the other problem is I have in stock 32×1617 £46.58
    but it is not the same, housing is but motor isn’t is it inter changeable? stoves gives me a part number STV082613062 £127.85 but no picture. My worry is why I was getting no power to it?
    Serial number 3 12 04058
    Thanks again Kirk

  • Author
    Posts
Viewing 15 posts - 151 through 165 (of 250 total)
1 2 3 … 10 11 12 … 15 16 17