[lerch]

Re: Whirlpool AWO/D4505 W Machine

Check motor brushes.

[lerch]

Re: aqualtis dead

Normal fault is display board as mentioned above. 😀

[lerch]

Re: TCR13 drum shaft kit replacement

Not really only a normal hpt condensor dryer just take outside takes about 20 minutes.

[lerch]

Re: Sertronics- Walsall

Yes if the company owner is called Adrian Anderson.

[lerch]

Re: samsung P1253

AS above if load cannot be balanced it will reset time and try again.

[lerch]

Re: Servis m6500 motor wiring

PM me your email as I have a wiring diagram if this will help. 😀

[lerch]

Re: LG RC8003a TE3 fault

tE 1 Low temperature thermistor open
tE 2 Low temperature thermistor short
tE 3 High temperature thermistor open
tE 4 High temperature thermistor short

tE1 : Check the main PCB red 4 pin housing not inserting Blue harness in red 4 pin
( number 2 , 4 )
Low temperature thermistor connector not inserting
Main PCB Micom not soldering replace Main PCB

tE2 : Check the main PCB red 4 pin housing Short of Blue harness in Red 4 pin.
Low temperature thermistor short : check the resitance.

tE3 : Check the white 8 pin housing (No. 3,4) in main PCB.
And Check the high temperature thermistor connector in rear cover part. ( blue wire )

tE4 : Check the main PCB White 8 pin housing.
Short of Blue harness in White 8 pin.
High temperature thermistor short : check the resitance.
Main PCB Micom short replace Main PCB.

EHE (ELE ) (Heater if memory serves me corretly)
Case 1. When break out or irregular current occurs.
– After removing ELB Connector, operate full time 1Cycle.
Case 2. EHE (ELE) message expresses continuously because of aging items.
– Change the old items.

be LED display “be ” in case of belt broken or pressed the micro switch by Motor bracket.
Main PCB Micom short replace Main PCB

Hope this helps. 😀

[lerch]

Re: PRO A10 Oven

If running for 30 minutes maybe getting to hot then safety toc’s kicks in and cuts power to oven then when cooled down will restart.

Sounds like a thermostat or has appliance go a cooling fan ?

[lerch]

Re: aeg f44050 v1

Intervention of Anti-flooding system
(the drain pump switches on)

The cycle is interrupted and the drain pump switches on check for leaks.

Do not think the model is correct as not rec. on zanussi / aeg website ?

[lerch]

Re: Whirlpool G2P90F/SS Oven 854184615021

It is quite hard to tell from the picture if this element is for the top oven or bottom oven.

4819 259 28847 Heating element lower is the part number if it is.

F01 Open or short circuit
of the temperature probe
Replace the temperature probe

F02 Overheating of the oven Replace Capricorn
(oven power unit)

F03 Capricorn not properly configured Replace Capricorn
(oven power unit)

F04 WISP protocol doesn’t work
(communication error)
Replace Capricorn (oven power unit)
or replace Scales (hob control unit)

[lerch]

Re: Help! Need Servis user manual

I have got one in pdf format for a M6500W if any help but only 2 pages not really much help but I can send. 😀

[lerch]

Re: I`m Assembling My Own Computer – Advice Please

I did build myself one about 4-5 years ago took 30minutes not really that hard.

The hardest bit is deciding how much to spend, what you want it to do, will all the parts work together and last is a laptop of more use ???

A good site for starters is http://www.ebuyer.co.uk that is where I got my parts from.

http://www.custompc.co.uk/

For examples of peoples wierd and damm right good self builds.

http://www.computerbuyer.co.uk/

there is also a forum on both which gave me loads of FREE ADVICE from people who seem to bloody know everything but without being snotty !!

other sites which may help:-

http://www.pro-clockers.com/
http://www.overclockers.co.uk/
http://www.xcase.co.uk/
http://www.crucial.com/
http://www.coolercases.co.uk/
http://www.goldchip.uk.com/

😀

[lerch]

Re: Supplier of Captive nuts

I have found that when changing stats on refrigeration there are usually a couple in there just put them in my tool box and there when needed.

I have tried looking but everyone is about £10 for 50ish. just do a online search for them.

[lerch]

Re: I`m Assembling My Own Computer – Advice Please

unless you are going to play games it will be just as well to buy one from a shop and more than likely cheaper.

[lerch]

Re: Comet Engineers

First question do you or have you worked for Comet ???

Second point, the reason why our depot is hiring is not because of the Samsung contract but due to uplift in work and has been for the last 3-6 months.

Third the samsung modi takes 10 minutes so hardly worth hiring just for that if we all did 5 a day extra would only add about 1-1 1/2 hrs onto our day which we get paid for anyway.

Fourth you have no idea how much we are being paid and lastly it is worth it considering how many we have sold of just rs21’s.
😀

[Author]

Posts