[loopey]

Re: New Van

ahhh the word scudo makes me spit lol very expensive to repair
clutch was £490 exhorst was £500 indicater relay was £61 please dont buy one lol , but was a good van to say the least 🙂

phil

[loopey]

Re: frigidaire fre196a

insulations gone ? nothing you can do with it i am afraid, tell customer to live with it or buy a new one ..

phil

[loopey]

Re: amana f/freezer

Dont no about the amana f/f but most ive changed are external of the f/f
just follow the plumbing to f/f 🙂 , theres usually a reset in the instruction book , usually press 2 buttons for 5 secs ..

hth phil

[loopey]

Re: Integra customer service number?

you could try service force they took over whirlpool repairs .

as far as i no they are whirlpool made ????

[loopey]

Re: frigidaire fre196a

Could be 1 of 3 faults that can cause this , low on gas , blokedge ,or weak compressor
the 1st 2 is more than likley , is it switching off at all ?? , is compressor mad hot , iff
the wet wall doesent get cold enough to open the stat , And is the freezer chocked up with ice
Have fully defrosted a couple like this and have gone back to normal,

hth phil

[loopey]

Re: Six year responsibility!!!.

Hi all
We have had a lot of phone calls and letters on this point , since its been advertised on tv as consumer law ..heres a typical letter we have been getting latley .

Dear Mr Poole

On 14th February 2008 I purchased a New World Built in Double Oven from your store in Platt Bridge. On 16th July 2009 it developed the following fault, the oven failed to warm up. The small oven is still working and the fan on the double oven is coming on but the oven will not warm up.

Under the provisions of the Sale of Goods Act 1979 I am legally entitled to request that you repair the item purchased or provide me with a satisfactory replacement.

Please send me a written response detailing your proposals within 7 days from the date of this letter.

Yours sincerely

Susan Payne (Mrs) yer lol pain is the word 🙁

In other words she is demanding a free repair or replacement,After 14 months trouble free cooking lol , spoke to customer for over an hour , that were here to help , and we will do as much as possible to help her out , we even offerd her to fit the part for free as long as she orded the part her self ,

and to bring in the cooker to our workshop ..

CUSTOMER said i no my rites i am in the LAW CLUB , this is not good enough will see you in court .

I said have a nice day , bang went the phone ..

I will sleep soundly as usual after reading kwatts posted article Big thanks to UKw

Will let you all no how we get on
regards phil

[loopey]

Re: hoover hw120m

Iff its got a 90 deg button , check the resistor across the terminals has not
gone O/C or come adrift . or iff it has a sprint pcb on it , change it .
hth phil

[loopey]

Re: Hoover VHD 8142 Vision 8kg

1st of all meggor the heater low insulation can cause alot of silly faults
even O/C heater will stop it spinning , and other things . count the flashes
every 15 secs should give you a fault code .

phil

[loopey]

Re: Hotpoint DC28 Slimline Dishwasher

turn the plastic ferrule with the 4 notches , use a peace of wood 5 n half inches
by 1 inch , one swift click anticlockwise and off it comes , i would check for
pin holes in the stainless steel 1st tho , had a few like that 🙂

phil 😆

[loopey]

Re: hoover vhd8142

give me email will send you a link 🙂 it looks like a complete front ….

[loopey]

Re: Hotpont FFA91G too cold in fridge.

it gets worse , on the latest HPTs f/f its foamed in to the carcass and coverd with the inner liner , just a little bump sticking out . lol 👿
phil

[loopey]

Re: hoover Nextra shot spin

no it should spin ok all way through , iff theres a fault it will through up a fault code , meggor the heater as that wont show up as a fault as that will stop it spinning .. 🙂
phil

[loopey]

Re: Hoover Fault Codes

The time for the displaying of each code, is 15
seconds. During this period of time, both LEDs flash
together at the frequency of 1 Hz (one flash per
second), for a number of times corresponding to the
number of the error to be displayed. Then, they stay
OFF for all the time that’s missing to the end of the
period of 15 seconds. The sequence is repeated until
Service Intervention or until the machine is switched
OFF.
Example: Error Code Number 2 (missing completion
of the water load within the designed limit
time) is displayed as follows:
• 2 flashes by the 2 LEDs together, in
the first 2 seconds of the period of 15
seconds (0.5″ ON – 0.5″ OFF)
• For the remaining 13 seconds, both
LEDs stay of OFF.
• The sequence as above, is repeated.
ERROR 2
The Water Fill Phase was not completed within the designed limit time. Defective
Solenoid Valve, Pressostat, Water Fill Hose, Low Water Pressure in the network
and/or Wiring.

hope this helps
phil

[loopey]

Re: re bearings on an Indesit WD 12 S UK

1st thing to check is to see iff inner drum has not rubbed away the outer
drum , have a look just above the heater is were it goes .. got caught out on this one this last week . spent half an hour putting bearings in and finding outer tub gone 🙁

phil

[loopey]

Re: Known Error Codes

candy grando series

The Error Codes are displayed through the simultaneous flashing of the FIRST LED of the
Chronovision series and of the LED of the FIRST OPTION BUTTON together.
The time for the displaying of each code, is 15 seconds. During this period of time, both LEDs
flash together at the frequency of 1 Hz (one flash per second), for a number of times
corresponding to the number of the error to be displayed. Then, they stay OFF for all the time
that’s missing to the end of the period of 15 seconds. The sequence is repeated until Service
Intervention or until the machine is switched OFF………..

ERROR 0 Defective “Cuore” Control Module – Not Programmed “Cuore” Control Module.
ERROR 1 Door Safety Lock Device/Drum’s Braking device defective and/or Wiring.

ERROR 2The Water Fill Phase was not completed within the designed limit time. Defective
Solenoid Valve, Pressostat, Water Fill Hose, Low Water Pressure in the network
and/or Wiring.
ERROR 3 The Water Drain Phase was not completed within the designed limit time. Clogged
Filter, Drain Pump, Drain Hose, Wall Discharge and/or Wiring.
ERROR 4 Several (3) interventions by the Anti-flood Safety Contact of Pressostat. Solenoid
Valve blocked opened, defective Pressostat and/or Wiring.
ERROR 5 NTC Temperature Reading Probe opened or shorted and/or Wiring.
ERROR 6 Eeprom – Defective “Cuore” Control Module and/or Wiring.
ERROR 7a (MDL) Jammed Motor’s Rotor and/or Wiring.

ERROR 7(INVENSYS) 7 Defective Door Safety Lock Device (blocked closed) and/or Wiring.
ERROR 8 Defective Tachometric Dynamo (opened or shorted) and/or Wiring.
ERROR 9 Defective “Cuore” Control Module (damaged Motor’s TRIAC) and/or Wiring.
ERROR 12 Missing dialogue between “Cuore” Control Module and Display board and/or
Wiring.
ERROR 13 Missing dialogue between “Cuore” Control Module and Display board and/or
Wiring.
(MDL) – Defective “Cuore” Control Module and/or Wiring.
ERROR 14 (INVENSYS) – Missing Water Heating: defective NTC Probe and/or defective
Water Heating Element and/or Wiring.
ERROR 15 Defective “Cuore” Control Module – Not Programmed “Cuore” Control Module.
ERROR 16 Water Heating Element is short circuited or defective electrical insulation.
ERROR 17 Wrong signal from Tachometric Dynamo.
ERROR 18 Defective “Cuore” Control Module and/or Wiring – Wrong Network Frequency.

phil 🙂

[Author]

Posts