Forum Replies Created
-
Posts
-
Re: Bosch bearing job in under 18 minutes! Pretty good.
ok i had to laugh at the rubber hammer and the bolt he used to knock in the bearing . yes i am sad had to try it on a wma housing , well i hope you all guess at what happend .. IT DIDENT
oHH BY THE WAY IT WAS A 30MIL KIT .. COMPLETE bull **it ..
as far as i am conserned lolRe: Candy G0282 (washing machine)
found this intresting it may help tho
A) DESCRIPTION OF THE TROUBLE:
We’ve recently been informed of some rare cases of the trouble as in subject, where the
selection of the “Easy Ironing” function coupled to one of the Washing Programs of the ranges
for Mixed & Delicate Tissues, was apparently resulting into a never ending Washing Phase.
Since the Phase of Washing is not going to end normally, it’s then necessary to move the
Programs Selector knob back to the OFF position, and keep it there for some moments. Then,
manually set the “Rinse Only” Program, to end the washing.
B) SOLUTION OF THE TROUBLE:
The “Cuore” Power Module originally fitted in the Factory on the Appliances as in subject, is
not reliable enough and must not be reprogrammed. Therefore replace the original Power
Module with a not programmed spare one by GIAS and P/N. 49019555. Program the new
Power Module with the related Software, with the MEM Programming Tool.
Should the MEM Programming Tool not be available, please order to GIAS the related already
programmed Power Module, getting its part number from the Spares List of the Giastech Web.Re: Hoover WMH148DF washing machine error E15
Defective “Cuore” Control Module – Not Programmed “Cuore” Control Module.
Re: Tefal Steam Generator help
9 times out of 10 its the cable between the iron and the base .
check the cable at the base end a good tug on the inner cables will tell wich has brocken and how far to cut back the outer shroud and the steam pipe , hope this helps yer done a few nowphil
Re: whirlpool arc 7410 cutting out
what capacitor did you change ?? usually its the o.22 uf cap on the pcb …
phil
Re: Hotpoint 9414 twin tub
no need to remove gearbox .. cabinet off , tripod off , Big plastic nut off at bottom of tub .disconect all leads from tub
and sump hose , now its been a while since ive done one ….
now you should be able to pull the top up and to one side so you can remove the tub at an angle ,3 bolts hold the surport
shaft , and off you go replace the new surport shaft and rebuild . dont for get the tub seal lol , no glue or debore needed ..wow that brought some memories back , now iff ive forgot some thing please comment ..
phil hth
Re: WD440 locked but not locked???
yes it can , but check the thermister on the wash heater 1st or the leads to it , had one last week the core of the thermister leads had broken at the connecter block dident show up a fault code 🙁
Re: HOTPOINT WML560 doesn’t start although door locks
1st i be looking at motor brushes and motor plug
Re: Where’s everybody gone?
All i can say is well done ken on a great looking site , much faster much eaiser to use , so come on kids stop wingering about change , we all have to change with the times , abit like getting a new digital megga , now what is that reading mean lol not were the needle goes . get used to it 🙂
Sorry iff of topic , but we did loose helo he said its gone crap but i dare say he will be back …Re: Hoover WDM120-01 No heat
check the 90 degree button it has a resitor across the terminals
iff that goes o/c it will not heat ..Re: Miele T7634
bump … has any one got one of these knocking about i have the rest of it now . or a part number for connections
Re: Hotpoint Supermatic Twintub 1464
Gearbox spigot tripod/post seal washer t/t 1460 1464 1465 1466 1467 1469 14860 14870 14890 9400 9402 9404 9410 9414 (5031680909098)connections part number now £16.83 new pence
yes had a few over the years with pin holes in the tub
phil
Re: Hoover Optima Range
timdowning wrote:All cases were nothing to do with being out of balance, all cases when a spin was selected the machine would start a wash cycle.
Again all other selections are perfect. (Selector issues Ive had before have been iffy on other programmes.)They buy crap, they get crap…fair exchange, no robbery.
A bit harsh Martin. To date, touch wood, Ive found the Optima range a good buy. Still waiting to see how the sealed drums hold out but still early days. Ive never understood why the majority of people on this site are so negative towards Hoover.
Thanks though for your explanation on OOB. 😉yes a little harsh there martin.. as we sell an awfull lot of hoover candy, dont really have any problems at all with this range or the rest of them , probs one of our most reliable and trust worthey we sell . look at the forums see how many bosch and zanussi questions there is ? not many hoover candy . :boops: sorry :offtopic:
Selector every time 🙂
