mbdas

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 317 total)
1 2 3 … 20 21 22
  • Author
    Posts
  • November 11, 2022 at 8:49 am in reply to: Neff C1apg64nob Combi oven #484369
    mbdas
    Participant

    Sorry I hadn’t finished typing the adverts got in the way E50.04
    does anyone know what they mean ,
    thanks mark

    January 28, 2021 at 10:11 am in reply to: Bush wmnsint612w door handle #474765
    mbdas
    Participant

    Thanks Dave will do , connect can’t supply it
    Mark

    January 27, 2021 at 2:52 pm in reply to: Bush wmnsint612w door handle #474763
    mbdas
    Participant

    Yes its D6155172401183085H0100
    mark

    January 27, 2021 at 1:45 pm in reply to: Bush wmnsint612w door handle #474761
    mbdas
    Participant

    Sorry no, there was no ratings plate on the front just a model number and a bar code, as it was built in I didn’t want to pull it out for just a door handle
    mark

    April 28, 2020 at 1:31 pm in reply to: Bosch wak24260gb/11 won’t spin #468320
    mbdas
    Participant

    Thanks Dave I have got a pair of gen hotpoint brushes which fit that motor I’ll give them a try and let you know
    regards mark

    April 28, 2020 at 12:59 pm in reply to: Bosch wak24260gb/11 won’t spin #468318
    mbdas
    Participant

    Yes but couldn’t feel any raised segments
    mark

    February 2, 2019 at 11:00 pm in reply to: Work table #460310
    mbdas
    Participant

    Thanks Dave I’ll have a good look tomorrow
    mark

    July 24, 2018 at 7:40 pm in reply to: Rangemaster excel 110 g5 induction cooker #456942
    mbdas
    Participant

    Re: Rangemaster excel 110 g5 induction cooker

    Thanks Dave it does, if I order the main board and the other 2 as no rings working now does the main board come with programming instructions?
    Thanks again mark

    May 11, 2017 at 7:26 am in reply to: Maytag Gs2625gekb module #447505
    mbdas
    Participant

    Re: Maytag Gs2625gekb module

    Thanks for that I’ll get it ordered then,
    Regards mark

    May 10, 2017 at 5:42 pm in reply to: Maytag Gs2625gekb module #447497
    mbdas
    Participant

    Re: Maytag Gs2625gekb module

    Thanks Dave
    I will also post in trade technical as don’t want to order it if I can’t programme it
    Regards mark

    February 2, 2017 at 5:44 pm in reply to: Hotpoint lst216 a fault code needed #444988
    mbdas
    Participant

    Re: Hotpoint lst216 a fault code needed

    That would explain why I can’t find a faulty part in it
    Thanks for the quick response
    Regards Mark

    September 15, 2015 at 10:44 am in reply to: Samsung Rsh5sbbp1 compressor won’t run #430159
    mbdas
    Participant

    Re: Samsung Rsh5sbbp1 compressor won’t run

    Hi I’ve looked under the lid and circuit boards but no information sheet anywhere that would have been to easy, the led flashers once followed by a pause then repeats any ideas . Thanks Mark

    May 16, 2015 at 7:41 pm in reply to: Whirlpool American dryer 3rleq8033sw1 heating problems #427362
    mbdas
    Participant

    Re: Whirlpool American dryer 3rleq8033sw1 heating problems

    Thanks for the info & web site just discovered one of the stats was the wrong part listed on connects web site, hopefully if I fit the right one this should sort it . Thanks Mark

    October 13, 2014 at 10:05 pm in reply to: aeg F50730 91123251701 dishwaser #420327
    mbdas
    Participant

    Re: aeg F50730 91123251701 dishwaser

    Thanks yes def worth a try
    Thanks mark

    October 12, 2014 at 9:51 am in reply to: Samsung rsh1nhmh ice build up around fan in fridge #420296
    mbdas
    Participant

    Re: Samsung rsh1nhmh ice build up around fan in fridge

    Thanks Bob I’ve been doing a bit of googleing 😆 so I think I will go armed with this part SAMDA8101997A cover support so hopefully this might do the trick.

    Mark

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 317 total)
1 2 3 … 20 21 22