Forum Replies Created
-
Posts
-
Re: CDA DISHWASHER
Hi, Thanks for that Penguin and no its just my eyesight its a lot easier to read in upper case
Thanks again MarkRe: CDA DISHWASHER
HI ,NO ITS NOT THAT PART 481241818337 ITS THE PART UNDER THAT WHICH ALSO HOLDS THE LOWER SPRAY ARM ON CAN YOU HELP WITH THE PART No OR AN EQUIVALENT WHIRLPOOL MODEL.
THANKS AGAIN
MARKRe: Matrix Dishwashers?
haier chaps,
had a call last week to a Haier d/w machine 2-3years old spent one whole hour or more trying to get it out, normal thing new laminated floor fitted right up to kick board.After removing kick board (had worse)adjusted front feet up pulled d/w forwards and got it half way out and machine stopped, electrical cable was run under d/w between front and rear feet went to adjust rear feet up this was done from the front, a small 1/4″ bar runs from the front to a mechanism which moves the rear feet up and down good idea until the plastic cogs in the mech breaks what a job i had lay on my back sawing the metal feet to get it out
Also had one a few years back when a GAS pipe was run under the d/w between the front and rear feet!Mark
Re: Whirlpool/CDA Dishwashers with Askoll Circulating Pump
HI I GOT ONE DOING THE SAME SYMPTON BUT HAVE FOUND THAT THE PLASTIC FUNNEL ON THE INSIDE OF THE DW KEEPS BLOWING OFF AND THE COVER WHICH HOLDS IT DOWN WAS BROKEN
HOPR THIS HELPS
MARKRe: AMERICIAN TOP LOADER
HI IF I ORDER THE GEARBOX 481903949118 DOES THIS COME WITH THE CLUTCH COZ IF IT DOESN’T ITS GOING TO BE VERY EXPENSIVE I MAY NEED TO HAVE ANOTHER LOOK
MARKRe: COMPRESSOR CHANGE
THANKS FOR THE ADVICE IT WAS SOMETHING I USE TO FIND INTERESTING AND WAS THINKING ABOUT GETTING BACK INTO IT,MY OPTION WAS TO SPEND SOME MONEY ON TRAINING MYSELF IN THIS AND BUYING THE EQUIPMENT NEEDED OR BUYING A NEW PAT TESTER IM NOW 75{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} FOR A NEW METER
THANKS FOR ALL YOUR COMMENTS
MARKRe: P A T (Portable Appliance Testing)
Hi Guys,
just did the course before xmas as i was going to offer this service but after get qualified city & guilds 2377 inspection and testing of electrical equipment which is the easy bit , the most inportant bit is the time it takes to do it and the equipment needed just dont have the time and can earn more repairing appliances and repairs are not boring , pat testing is ok if thats all you are doing but im sure you would soon get fed up of it. 🙂
markRe: Adjusting pressure switches
I’ve adjusted pressure switches before with no ill effects mostly on single or double level switches after cleaning out pressure chamber mostly on older candy dw unscrew to lower the level but if water has got in bin it
never had much luck with hvr triple level ones. i think philco sent out a memo to there agents telling them how to do this years ago maybe you can get an old copy if anyone has one .
MarkRe: whirlpool american toploader
£55 all in job done didn’t like to charge more as she has been waiting nearly 2 weeks as one cockup and another buy my supplier I thought she had been waiting long enough 7 in the family how high is her wash pile 😳
Re: whirlpool american toploader
Hi thanks for the advice i have only just receive part and have now fitted it, removed cabinet inorder to fit it found it dead easy I have found a web site in US with detail instructions of how to fit part if anyone is interested
http://www.repair2000.com its even got pictures
thanks again Mark 😛Re: CDA BUILT IN OVEN
Thanks for your help and your time, but the customer has gone to manchester to get one as they wont wait so Ive lost what little profit I would have made on the part.Hope it’s the right part he brings back as it’s a long drive if he has to take it back but thats his problem now.
Whilst searching for this part which does seem to be made by delonghi
I found CDA customer services tel No if anyone needs it 01949 862012
thanks again for your time
MarkRe: Part P Or Not To Part P
HI, had a email from dasa and they say it does NOT affect repairs to cookers but if you replace an existing cooker without rewiring and carry out a soundness test on that circuit then part p is satisfied but if you have to rewire or replace the circuit you have to be part p,
😛 😛mark
