[mbdas]

Re: BRANDT WFH1671U BEARINGS

Thanks for the advice, I’ve put a small amount of grease on the outer part of the seal and it has done the job so I’ll see how long it lasted
thanks
Mark 🙂

[mbdas]

Re: Bendix BDW 53 Dishwasher – access to drain pump???

Hi Electrue do a non gen pmp9004 as Penguin says remove motor its easier that way I’ve replaced a few of these motors as it does not seem to run fast enough to drain all the water out but washer fine
mark

ps you need a towel 😆

[mbdas]

Re: WHIRLPOOL ARZ896-1/H/SILVER

Thanks for that I’ll give them a ring after the bank holiday 🙂
Mark

[mbdas]

Re: WHIRLPOOL ARZ896-1/H/SILVER

So I need to approach Whirlpool then?How much does this cost?as I will have to way up the pros and cons. I only wanted it because I have just had the TDS one and that has paid for its self the first week I used it so was going to try SIOS also are there any more manufa selling these dvd’s

Mark

[mbdas]

Re: WHIRLPOOL ARZ896-1/H/SILVER

Not heard from rep re whirlpool disc can one of you please give me a part No and price
thanks again Mark 🙂

[mbdas]

Re: Tricity Bendix AW1050

Hi
Had same fault taco magnet loose in motor, machine advanced to end of cycle and didn’t even serge.

Mark

[mbdas]

Re: DIPLOMAT ADP3421/1 DOOR

Thanks for that, spoke to vague lady for mfi spares place and she said spares for this model were getting very difficult to get hold of she doesn’t have a price to hand but was sure it was expensive 🙄
Thanks again
Mark

[mbdas]

Re: WHIRLPOOL ARZ896-1/H/SILVER

Hi,
Thanks for that electrue rep call this morning he is going to enquire about disc.Is this better 😆

[mbdas]

Re: brandt wfh1671u bearings

HI,
CALLED BACK TODAY AND REMOVED BEARING SPIDER I WISH THEY WEAR ALL THAT EASY. IT HAD TAKEN ME LONGER TO REMOVE TO APPLIANCE FROM TO WASH ROOM TO WORK ON IT,THIS WAS BY FAR THE WORST APPLIANCE I HAD TO REMOVE FOR A VERY LONG TIME I MAY WELL TAKE MY CAMERA NEXT TIME AND POST A TOPIC FOR WORST SITUATED MACHINE HOPE TO GOD THE DRYER DOESN’T PACK UP COZ THATS ON TOP.
THANKS AGAIN
MARK

[mbdas]

Re: brandt wfh1671u bearings

Thanks for that guys i had already quoted her brandt prices and you can guess what she said,but having read your comments i ve since adviced her there may be an alternative and going back on tuesday 😛

[mbdas]

Re: WMA Bearing Seal

Ive replaced a few drum spiders and have stripped the heads off the drum bolts and broken torx bits i now quote for replacing to bolts and drill them out with a good drill bit as the heads are quiet soft and its quicker than struggling with them
mark

[mbdas]

Re: brandt wfh1671u bearings

THANKS FOR THAT.
IVE JUST BEEN QUOTED £25 FOR THE SEAL,£40 AND £36 FOR THE BEARINGS PLUS VAT & PP
I’LL GIVE HER A QUOTE AND TAKE IT FROM THERE,MAY STRIP IT DOWN AND TRY AND GET NUMBERS OF THE BEARINGS,
WOULD YOU SPEND NEARLY £200 ON A 2YR OLD BRANDT?
THANKS
MARK

[mbdas]

Re: NEED BELT FOR MAKE UNKNOWN

Thanks for that but ive sorted it now. never heard of that make before
thanks mark

[mbdas]

Re: TDS 2005 DVD

HI
I orderd this it went onto backorder on friday and come with my next order on tuesday I was pleasently surprised

mark

[mbdas]

Re: Weird Part Price’s

Hi,
I wanted a oven element for a New World cooker phoned stoves up they wanted £52 for it plus extra £12 to get part in 48 hours put part no in electrue they wanted £49.35 including the vat so i orderd it part arrived nx day in a BEKO BOX put part No in seme £9.79 including the vat and its a gen part so i now feel very ripped off and p***** off i’ve a good mine to send it back pay the handling charge order one from seme and i would have made more money on it and proberly saved the customer a bit as well

MAD MARK!!!!

[Author]

Posts