[mbdas]

Re: WHIRLPOOL 3LSC8255EQ1 TOPLOADER

Thanks for the pictures Dave your a star I’m going back tomorrow afternoon to strip it down Ive asked her to empty the room so I can get to it properly whats the bet that she doesn’t do it toilet infront of washer amercian dryer next to it then a d/w with loads of coates, towels, dirty washing o yes and a sink 🙄
thanks again Mark

[mbdas]

Re: WHIRLPOOL 3LSC8255EQ1 TOPLOADER

Sorry Dave its between the gearbox and drum if I shine my lamp on it I can just about see it I dont have a parts break down so cant tell you what its call but its not that part unfortunately
mark

[mbdas]

Re: ARISTON LB12TUK HEATER BRACKET

THANKS AGAIN
MARK

[mbdas]

Re: CDA CW491/1 DISHWASHER

Thanks for that Dave Ive given the customer an esty
🙂

[mbdas]

Re: Whirlpool American Dryer

SEME PART number W3-65015 102mm 1.5m
W3-65025 127mm 3m
W3-65025 152mm 3m
between £4 &£10 plus vat
Mark 🙂

[mbdas]

Re: Bosch Vacuum

Its a Vax upright Ive replaced a few motors in these both the vax and bosch versions I spray a little polish on the rings and push the spring loaded pegs in and gently easy them over never had a switch in the base faulty though just plenty of motors
Mark 🙂

[mbdas]

Re: NEW WORLD FAN OVEN ELEMENT

Nice one Dave 😀
thanks
Mark

[mbdas]

Re: NEW WORLD FAN OVEN ELEMENT

Morning
Ive done some digging and have come up with this on electrues site they told me over the phone this was obsulete but 5031680839760 is listed for that model and they want £43.12 + vat to me can anyone give me the gen number so I can cross referance it

Mark

[mbdas]

Re: SERVIS M495 FILL FAULT

water had leaked from air break on the side into this and check with meter and it was o/c so shorted it out and it filled ok thats why I thought it was a fuse of some kind (looks like a microtemp but clear) but like dmp said try passing a magnet over it and it does go s/c and I cant remember if salt light was on ,but everway why would sorting it out make all the difference if it only controlled the salt fill light ❓ the machine beeps after 5 secs of fill and no fault code comes up .when you look at it carefully with a magnify glass in the middle there is a smaller piece of fine what looks like fuse wire solderd to the main points in it which I think may have made the circuit before the main contacts in it make ❓ ❓ also electrue have stock of the dispensors which may suggest they do go faulty ❓ This is the first one of these I’ve done so I’m a bit in the dark on this 🙂 thats why most of the smileys are the same ❓
mark

[mbdas]

Re: SERVIS M495 FILL FAULT

eye sea , 😮 so there must be a magnetic float of some kind inside of the container which is sticking or that the level is not correct inside of it.Told you it would cost me I’ll go back after the weekend and have another look before ordering a container.

thanks
mark

[mbdas]

Re: SERVIS M495 FILL FAULT

urmmm, it fits above the valve on the salt container the numbers on it are 005a220/240v TYPE GR100. what does the reed switch do ❓ this part just slides off and looks just like a fuse and is o/c, don’t want to order a complete container if it is just going to blow and a sods law this is in the middle of no where. I can see this job costing me, 🙁 so the more info I get the better 💡

mark

[mbdas]

Re: INDESIT W161UK INTERMITTENT FAULT

Its just funny how it works ok with nothing in it or wet washing checked pressure tube chamber and hose for holes etc if I let the machine fill up with pressure tube pipe off and blow into the switch it will go ok but if you blow a bit harder the pump comes in and it aborts my logic is the first level turns valve off and the next is anti flood so I thought the gap between the first and anti flood levels are to close I fitted a board and thermistor too

I wont let the bloody thing beat me 😥 I’ll check wires again
thought someone may have had same fault

mark

[mbdas]

Re: TECNIK appliances

Hi,
I’m sure Neff/Bosch make some of the newer ones if theres an ENr number on it you can get the part number from BSH web site
hope this helps
Mark

[mbdas]

Re: Insulation testers

Thanks for all the advice I’m still looking for a insulation tester I’ve also been considering a loop tester all in one but very pricey whilst looking around I’ve come across this Martindale ez750 Eze check loop tester
http://www.martindale-electric.co.uk
So I’m now considering one of these plus insulation tester will save a alot of money which will mean more for a beer 😉 as martin wrote most important bit of kit we use so will have more for it

mark

[mbdas]

Re: Tricity 4638 door hinge

Thanks I thought so, just thought there may be one out there somewhere
will give the customer the bad news. Its a shame coz I’ve seen more grease on a salad 😆
Thanks
mark

[Author]

Posts