MDE

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 66 total)
1 2 3 4 5
  • Author
    Posts
  • February 11, 2009 at 10:39 pm in reply to: Whirlpool awm9100/1 #276927
    MDE
    Participant

    Thanks bzz67,
    I have ordered that part so will have to wait and see,but it sounds good.
    Mark.

    November 13, 2008 at 2:42 pm in reply to: Bosch WFB2005 #266983
    MDE
    Participant

    Fitted a new timer to this machine to day and it is still doing the samething, I am still convinced the timer is at fault but this is a rented house and tenants do mess with the wireing in my experience, so would anyone have a wireing diagram for this machine.How unusual would it be for the new timer to have the same fault ?

    Thanks Mark.

    October 28, 2008 at 1:19 pm in reply to: AKP 201/IX [857720115520] #266408
    MDE
    Participant

    Re: AKP 201/IX [857720115520]

    jag-12 wrote:Dont suppose its a 701 rather than 201?

    I havent seen it so i will get the customer to double check it.

    Thanks Mark.

    October 24, 2008 at 12:29 pm in reply to: MIELE W820 Bearings #266334
    MDE
    Participant

    Seamy & Clayside thanks for the replies, with that info in mind I will carry out the repair, it will be nice to do something different for a change

    Mark.

    September 27, 2008 at 10:50 am in reply to: Whirlpool adg7550 #263519
    MDE
    Participant

    Thanks Martin. I will have to have a better look and see what i can find.

    Mark.

    September 11, 2008 at 11:54 am in reply to: Hotpoint VTD00 #262276
    MDE
    Participant

    helo_75 wrote: if you move the hinge to the closed position, it will slide down and pull out

    Hinges must be removed from the body of the machine. Then replace as above.

    September 10, 2008 at 2:14 pm in reply to: SOAPY DISHWASHER #262243
    MDE
    Participant

    Re: SOAPY DISHWASHER

    Martin wrote:Has she poured Fairy Liquid in the rinse aid compartment or detergent in the salt container I wonder?

    Thanks Martin,
    I don’t think so, barring the issue of washing’up liquid can you or anyone else think of anything that will cause this problem.

    Thank Mark.

    September 5, 2008 at 7:57 am in reply to: Whirlpool 3RLEC8646JQ td service manual #261691
    MDE
    Participant

    Hi mike, Have a look on Appliancejunk.com there are manuals for various American appliances so they may have it or one similar to it.

    Mark.

    August 7, 2008 at 10:17 pm in reply to: Samsung RS20CCSV #259310
    MDE
    Participant

    Thanks Bryan, I will replace the defrost sensor.

    Mark

    July 28, 2008 at 12:03 pm in reply to: Hoover WA110-01spin on wash #258543
    MDE
    Participant

    I have had more than one taco with a crack in it , I even had one go with a big bang on its first test wash after changing the module. Me not happy that day.

    Mark.

    July 2, 2008 at 9:40 pm in reply to: Servis M6725S Door seal #256485
    MDE
    Participant

    Connect have it in stock,

    RRP £38.31 + vat,

    Mark.

    July 2, 2008 at 9:27 pm in reply to: Bosch WFD2072GB/05 #256506
    MDE
    Participant

    Never did one myself so not much info for you.

    Front bearing P/n 154811,
    rear braring p/n 154812,
    drum shaft seal p/n 417478,
    rear tub p/n 475046,

    all part numbers from http://www.bosch-eshop.com

    hope this helps , Mark.

    June 30, 2008 at 10:22 am in reply to: INDESIT WG830 TPG #256172
    MDE
    Participant

    Thanks for all the replies, it turns out i have a set bearings {C00090555} that i got for another indesit job, only to find it was a sealed drum so i will now be able to use them.

    Thanks Mark.

    June 28, 2008 at 11:40 am in reply to: Hotpoint WD440 #255953
    MDE
    Participant

    Thanks for your reply A1.

    Now can anyone give me part numbers for board and eeprom or do i need more information.
    Thanks Mark.

    June 17, 2008 at 1:04 pm in reply to: teka w/d #255029
    MDE
    Participant

    Ignore last post, thought you were talking about a D.W.

    Sorry mark.

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 66 total)
1 2 3 4 5