mic

Forum Replies Created

Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • June 19, 2020 at 6:07 pm in reply to: Siemens 84E562GB microwave, cuts out after about nine seconds #469784
    mic
    Participant

    Thanks,
    will get this checked out, no obvious arcing sounds.

    April 19, 2018 at 7:19 pm in reply to: Bosch WAS287B0GB/23 #455416
    mic
    Participant

    Re: Bosch WAS287B0GB/23

    Thanks
    very useful information , I also found BSH00751791 which is grey, it eis strange that BSH told me I would have to buy a complete door, they are usually very good with their parts information.
    Michael

    March 17, 2015 at 5:30 pm in reply to: Whirpool AWZ121 Replace Start Switch – Wiring Advice #423045
    mic
    Participant

    Re: Whirpool AWZ121 Replace Start Switch – Wiring Advice

    Thanks for the above I have just been looking at one of these

    February 5, 2014 at 9:15 am in reply to: Hotpoint FF200E Fridge Freezer #251180
    mic
    Participant

    Re: Hotpoint FF200E Fridge Freezer

    Hi I see this is an old thread but if anyone could send us the info it would be really helpful
    Thanks
    Wendy

    December 19, 2012 at 7:51 am in reply to: JLWD1609 timer problem #386511
    mic
    Participant

    Re: JLWD1609 timer problem

    Thanks
    would the neutral supply being missing account for the timer issue
    Michael

    November 29, 2010 at 9:40 pm in reply to: LG WM1480FHD #337008
    mic
    Participant

    Re: LG WM1480FHD

    Hi
    thanks for reply, once it has switched on it will turn on and off as normal, it is only when it has been left off for some time it is reluctant to switch on again. It makes no differance if you push switch firmly or gently it just needs a lot of pushes

    September 9, 2010 at 5:57 am in reply to: Whirlpool tumble dryer fuse #329805
    mic
    Participant

    Re: Whirlpool tumble dryer fuse

    cornwell40 wrote:Is this the fuse in the loom at the top.
    Was advised years ago by an ex Whirlpool engineer, that there is (if I remember) a 6A fuse which regularily goes, was told to up the rating slightly.
    Have only done this once when a similar fault happened and it has worked merrily for years. Meggered all the usual suspects at the time and all tested perfectly.

    TC

    Thanks for your help, it is a 6.3 time delay in the loom at the top will try as you suggest. It all meggers ok and runs for months at a time with no problems.

    Mic

    June 23, 2009 at 8:08 am in reply to: Fault Code Guide #223282
    mic
    Participant

    Re: Fault Code Guide

    It’s been a few months, is there a new guide yet? or any idea when it’s likely to be available?

    November 17, 2008 at 9:10 am in reply to: wol2200gb bearing change #266444
    mic
    Participant

    Re: wol2200gb bearing change

    Thank you very much. I was still struggling with this one, what you sent will be extremely helpful, it’s much appreciated.
    Regards Michael

    August 4, 2008 at 6:36 pm in reply to: Indesit DI620uk PCB #253505
    mic
    Participant

    Re: Indesit DI620uk PCB

    Hi Thanks for your help

    September 16, 2007 at 2:17 pm in reply to: Bosch fridge hinges #227633
    mic
    Participant

    Re: Bosch fridge hinges

    Hi Greg

    there are no numbers after gb on appliance, but on BSH Appliance care site there are two versons both of which use part 489424.

    Thanks for your help

  • Author
    Posts
Viewing 11 posts - 1 through 11 (of 11 total)