mjhservices

Forum Replies Created

Viewing 15 posts - 61 through 75 (of 97 total)
1 2 3 4 5 6 7
  • Author
    Posts
  • January 17, 2011 at 5:43 pm in reply to: AEG Washing Machine L64810 #341552
    mjhservices
    Participant

    Re: AEG Washing Machine L64810

    how do you enter diagnostics on this model?

    November 12, 2010 at 2:36 pm in reply to: Hotpoint WD420 #335632
    mjhservices
    Participant

    Re: Hotpoint WD420

    Thanks but none of the above

    September 8, 2010 at 1:46 pm in reply to: HELP! Select 160 by Diplomat #329814
    mjhservices
    Participant

    Re: HELP! Select 160 by Diplomat

    Make sure the clock is set to manual otherwise it will not work.
    Turn the clock dial to the hand position.

    September 2, 2010 at 12:16 pm in reply to: Hoover VHD9143D #329408
    mjhservices
    Participant

    Re: Hoover VHD9143D

    Thanks for that. Can you tell me how to put this model into test mode?
    Mark

    July 8, 2010 at 8:10 am in reply to: Fill Time for a Dishwasher ? #324863
    mjhservices
    Participant

    Re: Fill Time for a Dishwasher ?

    I have had quite a few of these and its always been the water valve that needs to be replaced.

    July 7, 2010 at 8:16 pm in reply to: Water flow on Hotpoint #324849
    mjhservices
    Participant

    Re: Water flow on Hotpoint

    Yes all that has been checked also the water reducer in the valve .

    March 31, 2010 at 7:08 pm in reply to: Bosch WVTi3240GB/03 #316897
    mjhservices
    Participant

    Re: Bosch WVTi3240GB/03

    Thanks for the reply, but I think the pressure hose is clear because it was only cleaned out about a year ago and after filling it today many times the water level was exactly the same every time.
    Mark
    ps How is it a Bosch built/made by Smeg?

    March 1, 2010 at 6:16 pm in reply to: Diplomat Dishwasher ADP8332 #313509
    mjhservices
    Participant

    Re: Diplomat Dishwasher ADP8332

    Thanks for the info although I did tighten up the plug etc and it did not work.
    What does this part do?
    Regards Mark

    February 4, 2010 at 8:33 am in reply to: Electrolux EWX14440W #310908
    mjhservices
    Participant

    Re: Electrolux EWX14440W

    There was no error code it just said ERR
    Regards Mark

    February 26, 2009 at 6:49 pm in reply to: Smart Card Reader #278530
    mjhservices
    Participant

    Re: Smart Card Reader

    Thanks for your replys

    December 16, 2008 at 7:43 am in reply to: NTC 4812 237 08014 #271647
    mjhservices
    Participant

    Re: NTC 4812 237 08014

    Thanks Penguin

    November 6, 2008 at 7:44 am in reply to: Bosch Dishwasher #267532
    mjhservices
    Participant

    Re: Bosch Dishwasher

    No its not the valve as I have checked this from the other end to see the speed the water comes out when turned on.
    Mark

    October 21, 2008 at 6:32 am in reply to: Indesit WIL113 #265885
    mjhservices
    Participant

    Re: Indesit WIL113

    As I thought, thanks Penguin

    September 10, 2008 at 4:10 pm in reply to: Hotpoint VTD00 #262273
    mjhservices
    Participant

    Re: Hotpoint VTD00

    Hi Martin
    There is no way this inner door is a push fit into the hinge. Myself and others can not see how this is possible.
    Mark

    September 10, 2008 at 2:57 pm in reply to: Hotpoint VTD00 #262271
    mjhservices
    Participant

    Re: Hotpoint VTD00

    Thanks for your reply but the problem is separating the inner door from the hinge.

  • Author
    Posts
Viewing 15 posts - 61 through 75 (of 97 total)
1 2 3 4 5 6 7