Penguin45

Forum Replies Created

Viewing 15 posts - 3,901 through 3,915 (of 19,678 total)
1 2 3 … 260 261 262 … 1,310 1,311 1,312
  • Author
    Posts
  • February 3, 2009 at 12:24 am in reply to: zanussi DE6744 #252510
    Penguin45
    Participant

    Re: zanussi DE6744

    There are retaining screws behind the kick panel. That’s held by two screws. Get rid of that, then you can access them. Once undone, it’s a lift and pull to release the panel.

    Penguin45.

    February 3, 2009 at 12:16 am in reply to: apm8552 #275996
    Penguin45
    Participant

    Re: apm8552

    720090100 – drum and shaft.
    402011900 – tub gasket.

    Chris.

    February 2, 2009 at 8:39 pm in reply to: Neff Fridge/Freezer #275245
    Penguin45
    Participant

    Re: Neff Fridge/Freezer

    “Frost free” does not mean that it never needs defrosting. Article HERE.

    Penguin45.

    February 2, 2009 at 8:15 pm in reply to: FLE1216W Flashing Lights #276084
    Penguin45
    Participant

    Re: FLE1216W Flashing Lights

    Yersss – see what you mean about the binary code. Well, all the E6- codes relate to temperature issues, so I suppose that’s somewhere to start. 🙁

    Chris.

    February 2, 2009 at 8:02 pm in reply to: Door Fixing instructions for Integrated Whirlpool. #275654
    Penguin45
    Participant

    Re: Door Fixing instructions for Integrated Whirlpool.

    Full height door or “drawer line”?

    Penguin45.

    February 2, 2009 at 7:56 pm in reply to: Hotpoint WT940 – Wrong Pump? #276090
    Penguin45
    Participant

    Re: Hotpoint WT940 – Wrong Pump?

    The switching triac for the pump will have failed in the “on” position, which is why the pump is running continuously. Triac is part of the main pcb, so you either work out a board level repair or replace the board.

    Penguin45.

    February 2, 2009 at 7:52 pm in reply to: FLE1216W Flashing Lights #276082
    Penguin45
    Participant

    Re: FLE1216W Flashing Lights

    Turbo wrote:Oops could someone move it for me 😳
    Graham

    Oh, all right then. 😀

    Chris.

    February 2, 2009 at 5:38 pm in reply to: Softy southerner winging about snow #275934
    Penguin45
    Participant

    Re: Softy southerner winging about snow

    Heh – so my Scudo is:

    Snow
    Can’t
    Upset
    Daily
    Operations

    :snig:

    Chris.

    February 2, 2009 at 5:21 pm in reply to: Softy southerner winging about snow #275931
    Penguin45
    Participant

    Re: Softy southerner winging about snow

    St. Vitos Dance? Condition of helplessness caused by lack of traction…..

    :p45:

    February 2, 2009 at 4:40 pm in reply to: diplomat ADP8322 FAULT CODES – DIAGNOSTICS #275995
    Penguin45
    Participant

    Re: diplomat ADP8322 FAULT CODES – DIAGNOSTICS

    KNOWN ERROR CODES – bottom of page 1.

    Chris.

    February 2, 2009 at 4:33 pm in reply to: Softy southerner winging about snow #275928
    Penguin45
    Participant

    Re: Softy southerner winging about snow

    8 calls completed – what’s all the fuss about?

    Chris.

    February 2, 2009 at 12:26 am in reply to: Candy C1260 – Not Draining #275915
    Penguin45
    Participant

    Re: Candy C1260 – Not Draining

    Drag it out. Pull the plug. Stick drain hose in the washing up bowl and drain the machine. Tip it back and locate the drain pump. You will have to remove the pump cover and see if there is an obstruction – coins can cause an intermittent problem. If there is nothing there, you will need to fit a replacement pump. THIS is a suitable replacement.

    Penguin45.

    February 1, 2009 at 9:23 pm in reply to: Whirlpool AWM029 – door lock/unlock problem #275902
    Penguin45
    Participant

    Re: Whirlpool AWM029 – door lock/unlock problem

    Remove plug. Slip band from door seal. Unhook door seal from front panel. Undo the two screws for the door lock. Undo three screws at the bottom of the front panel and it will fall off, revealing the lock.

    Penguin45.

    February 1, 2009 at 8:51 pm in reply to: Indesit w93 programmer is doing the waltz! #275899
    Penguin45
    Participant

    Re: Indesit w93 programmer is doing the waltz!

    PCB is sending power to the motor, but it thinks that it is no responding. Check drive motor carbon brush gear, check wiring to motor and pcb – if all in circuit, the pcb is the culprit.

    Power off if you intend to do this yourself.

    Penguin45.

    February 1, 2009 at 8:47 pm in reply to: Belling IDW604 #274062
    Penguin45
    Participant

    Re: Belling IDW604

    It appears to be one of the Chinese machines. This sounds like a pcb failure.

    Penguin45.

  • Author
    Posts
Viewing 15 posts - 3,901 through 3,915 (of 19,678 total)
1 2 3 … 260 261 262 … 1,310 1,311 1,312