robbra

Forum Replies Created

Viewing 15 posts - 991 through 1,005 (of 1,090 total)
1 2 3 … 66 67 68 … 71 72 73
  • Author
    Posts
  • February 24, 2006 at 9:59 pm in reply to: CONDITIONER PROBS FOR service M6003 #166634
    robbra
    Participant

    Re: CONDITIONER PROBS FOR service M6003

    Touche Moik

    February 24, 2006 at 5:53 pm in reply to: CONDITIONER PROBS FOR service M6003 #166632
    robbra
    Participant

    Re: CONDITIONER PROBS FOR service M6003

    Butm if yoo boy ar guden loik them wuns in Seme, they cheepuns, yool av a tuffun.
    Roab

    February 24, 2006 at 9:44 am in reply to: CONDITIONER PROBS FOR service M6003 #166630
    robbra
    Participant

    Re: CONDITIONER PROBS FOR service M6003

    or
    Forgot to say last night(just back from the pub) thewater pressure is the deciding factor in where the water goes in the drawer.Too much or little can cause it to go into the wrong part and I have had this several times and usually fit a ‘Y’ peice to cure it as normally the hot lets it down
    Rob

    February 23, 2006 at 11:48 pm in reply to: CONDITIONER PROBS FOR service M6003 #166629
    robbra
    Participant

    Re: CONDITIONER PROBS FOR service M6003

    or
    tell her to use better fab cond and use less and don’t push the drawer in to fast as it syphons away
    Rob

    February 23, 2006 at 4:59 pm in reply to: module variations for Servis M9309 #166594
    robbra
    Participant

    Re: module variations for Servis M9309

    When I worked for SUK fitted 1000 (546004300) to most 900spin and had no probs. many Servis modules factory fitted don’t correspond to the specified spin speed
    Rob

    February 23, 2006 at 8:04 am in reply to: Not sure if this is an error code Zanussi #166281
    robbra
    Participant

    Re: Not sure if this is an error code Zanussi

    Thanks for that, and you are just down the road if I need help. Will let you know how it goes.
    Rob

    February 22, 2006 at 4:50 pm in reply to: Not sure if this is an error code Zanussi #166279
    robbra
    Participant

    Re: Not sure if this is an error code Zanussi

    Thanks Martin. looks like another for the scrapyard
    Rob

    February 22, 2006 at 3:52 pm in reply to: Not sure if this is an error code Zanussi #166277
    robbra
    Participant

    Re: Not sure if this is an error code Zanussi

    well no answers but live in hope.can anyone supply part no for main pcb. Thanks
    Rob

    February 20, 2006 at 7:04 pm in reply to: samsung washer pump #166268
    robbra
    Participant

    Re: samsung washer pump

    most of the pumps they use are Askoll copies so that may fit
    Rob

    February 20, 2006 at 12:21 pm in reply to: Servis M491W #166224
    robbra
    Participant

    Re: Servis M491W

    Hi, what is the residue? If it is food etc. then it sounds like the spray arm is being stopped from rotating by something in the bottom basket, especially if it is an intermittent fault. Is your top basket at the highest.ie the bottom wheels on this basket in the runners? If not raise it and try again. If residue is not food what does it look like?
    Rob

    February 20, 2006 at 11:43 am in reply to: Diplomat ADP8322 #164392
    robbra
    Participant

    Re: Diplomat ADP8322

    Blimey Chris.Have cancelled but can’t get under £30+ and haven’t got a Masterpart account. Can anyone help?
    Thanks
    Rob

    February 19, 2006 at 10:08 pm in reply to: Diplomat ADP8322 #164390
    robbra
    Participant

    Re: Diplomat ADP8322

    Thanks Dave. have ordered one but at £30 + vat it’s pricey but if it’s not that I will use it in time no doubt
    Rob

    February 16, 2006 at 10:29 am in reply to: Behnstein Group – Built in Fridge. #164335
    robbra
    Participant

    Re: Behnstein Group – Built in Fridge.

    This isn’t a Whirlpool, its a Merloni (Servis)

    February 14, 2006 at 12:36 am in reply to: Servis dishwasher impellor #164245
    robbra
    Participant

    Re: Servis dishwasher impellor

    Hi,
    Servis price £113.00 +vat via G B Dars

    February 11, 2006 at 12:06 pm in reply to: Does my Servis M0330s F/Free Fridge Freezer need new module? #161394
    robbra
    Participant

    Re: Does my Servis M0330s F/Free Fridge Freezer need new mod

    Hi .
    Pleased to know you are now ok. Sorry never got back to you but pc hard drive went down and couldn’t be fixed
    Rob

  • Author
    Posts
Viewing 15 posts - 991 through 1,005 (of 1,090 total)
1 2 3 … 66 67 68 … 71 72 73