S1MON

Forum Replies Created

Viewing 15 posts - 136 through 150 (of 151 total)
1 2 3 … 9 10 11
  • Author
    Posts
  • February 16, 2007 at 6:56 pm in reply to: Diplomat ADP 8324 #204543
    S1MON
    Participant

    Re: Diplomat ADP 8324

    ok cheers will have a look at that.

    February 16, 2007 at 6:03 pm in reply to: Bosch WTA3200GB/09 #204430
    S1MON
    Participant

    Re: Bosch WTA3200GB/09

    Went back today set it on manual and it heats but only sightly. Tried it again on setting one and it did the same.

    I replaced the board and duct sensor and left on setting one for 15 minutes and it appears to have done the trick. WAs getting nice and hot,

    Going back friday with a new plinth so we find out for definate then.

    Bit odd thou as everything belled out fine and the relay did switch on the old broad….

    February 12, 2007 at 6:58 pm in reply to: Hotpoint Mistral FF65P #203799
    S1MON
    Participant

    Re: Hotpoint Mistral FF65P

    went back today have moved the thermistor and rip tidied it to the evap, also checked the ducts and totally clear.

    Fans are both working ok

    M/C is on test lets see what happens

    February 11, 2007 at 5:54 pm in reply to: Hotpoint Mistral FF65P #203796
    S1MON
    Participant

    Re: Hotpoint Mistral FF65P

    Ok cheers ill try both these things and see how i get on

    February 9, 2007 at 5:25 pm in reply to: Bosch WTE5820gb/04 Condensing TD #203801
    S1MON
    Participant

    Re: Bosch WTE5820gb/04 Condensing TD

    lovely sounds simple

    January 14, 2007 at 9:08 pm in reply to: Testing or Bypassing Door Interlock #200475
    S1MON
    Participant

    Re: Testing or Bypassing Door Interlock

    Interesting point of view paul but your asking for a fall mate 😯

    Is the small cost of a door lock really worth it

    December 22, 2006 at 4:06 pm in reply to: Smeg A1 Range #198472
    S1MON
    Participant

    Re: Smeg A1 Range

    cheers again for the info 8)

    December 21, 2006 at 9:54 pm in reply to: Smeg A1 Range #198470
    S1MON
    Participant

    Re: Smeg A1 Range

    ok cheers alan but i have not recieved mail and im going back to this tomrorrow. I cant see from inspection any wiring running around the hinges???

    December 20, 2006 at 7:32 pm in reply to: Siemens Siwamat WXB860BY/05 #197929
    S1MON
    Participant

    Re: Siemens Siwamat WXB860BY/05

    I had similar today found the pump was very worn and noisy with alot of play on the impellor.

    December 20, 2006 at 7:19 pm in reply to: Smeg A1 Range #198467
    S1MON
    Participant

    Re: Smeg A1 Range

    cheers for that 8)

    December 20, 2006 at 6:58 pm in reply to: Smeg A1 Range #198465
    S1MON
    Participant

    Re: Smeg A1 Range

    sorry missed a bit from that

    gormansimon22@aol.com

    cheers Si

    December 18, 2006 at 8:24 pm in reply to: Belling DW problems #197994
    S1MON
    Participant

    Re: Belling DW problems

    Its not flashing a E number!

    Ill check the pressure system

    December 7, 2006 at 8:48 pm in reply to: Dodgy Hotpoint WM 52 #197329
    S1MON
    Participant

    Re: Dodgy Hotpoint WM 52

    christ your having all the luck by the sound of it 😯

    November 20, 2006 at 9:35 pm in reply to: ZANUSSI DISH DE6744 #175516
    S1MON
    Participant

    Re: ZANUSSI DISH DE6744

    interesting ive had one with a similar fault, doesnt seem to a definate answer with these……. ill jave a look at that rinse aid sensor. I also turned water pressure down and that caused it to work a few times??

    November 9, 2006 at 6:08 pm in reply to: Zanussi DE 6744 #191983
    S1MON
    Participant

    Re: Zanussi DE 6744

    Hi

    I have still got problems with the above Zanussi machine. It is coming up with a anti-flood fault. I have checked everyting but I can not see a float switch or mircoswitch anywhere on the machine. It does thou have a open base??? Slightly worrying! Its my old dears machine so I know it has never been touched before.

    Now I have had it running but it will intermitantly just do nothing flashing the anti-flood fault code. I have run it on a test cycle and everything works as it should, wiring and all components have been checked again.

    It is beginning to annoy me a bit, it just doesnt seem logical.

    I have been sent info on fault codes etc, gone throu all of this wondering if this is going to be another pcb….. or to the skip………

    Any ideas thanks

  • Author
    Posts
Viewing 15 posts - 136 through 150 (of 151 total)
1 2 3 … 9 10 11