Page 118 – UK Whitegoods

Forum Replies Created

Viewing 15 posts - 1,756 through 1,770 (of 2,216 total)

← 1 2 3 … 117 118 119 … 146 147 148 →

Author

Posts
December 30, 2005 at 6:30 pm in reply to: Indesit WG9 not Spinning #159300

Simon46
Participant

Re: Indesit WG9 not Spinning

Can you check the model number again?

Regards
Simon

December 21, 2005 at 7:40 pm in reply to: Whirlpool washing machine model AWM 8163 #158672

Simon46
Participant

Re: Whirlpool washing machine model AWM 8163

If you set it to spin only will it drain/ finish cycle.

Regards
Simon

December 21, 2005 at 7:38 pm in reply to: indesit w1101 washer #158677

Simon46
Participant

Re: indesit w1101 washer

Sealed off drain spigot?

S.

December 21, 2005 at 7:37 pm in reply to: Hpt condenser dryer no heat #158679

Simon46
Participant

Re: Hpt condenser dryer no heat

Did you check the stat at the front of the drum?

S.

December 20, 2005 at 11:07 pm in reply to: ASTRA EGR VALVE #158546

Simon46
Participant

Re: ASTRA EGR VALVE

Have a look at car transplants in northwich. Lots of late models breaking.

S.

December 20, 2005 at 10:59 pm in reply to: Zanussi FLA 1201W motor price #157246

Simon46
Participant

Re: Zanussi FLA 1201W motor price

Distriparts are showing in stock FHP but i am getting story that they cannot find them in warehouse. 2 Wks i have waited.

S.

December 20, 2005 at 11:18 am in reply to: Zanussi FLA 1201W motor price #157239

Simon46
Participant

Re: Zanussi FLA 1201W motor price

The motor on this model is a sole 124212303 480/14000 rpm. However the replacement is FHP 1243910005 which no one seems to have and is a fortune(masterpart). Would a sole motor from one of the other fla1201w machines listed fit. I notice that the other versions have 1242123014 listed. Is the last couple of digits a date code?

Regards
Simon

December 18, 2005 at 8:46 pm in reply to: Hotpoint aquarius tdc 30 cuts out at the start of cycle.help #158228

Simon46
Participant

Re: Hotpoint aquarius tdc 30 cuts out at the start of cycle.

In answer to your PM the relay is located behind the front panel with the lid off. Can be fiddly to replace. Always unplug power if you are going to have a go yourself :zap: .

Regards
Simon.

December 18, 2005 at 3:15 pm in reply to: Hotpoint aquarius tdc 30 cuts out at the start of cycle.help #158227

Simon46
Participant

Re: Hotpoint aquarius tdc 30 cuts out at the start of cycle.

That will be the relay http://www.ukwhitegoods.co.uk/modules.p … cts_id=301. Unplug power if you are going to have a look yourself. Or look at Repairs@ for an engineer.

Regards
Simon

December 11, 2005 at 10:53 am in reply to: Indesit WD12 drainage/noise problem #156583

Simon46
Participant

Re: Indesit WD12 drainage/noise problem

The pump could possibly be swopped onto the old filter chamber for a quick fix. You may need torx bits for this.

Regards
S.

December 10, 2005 at 10:46 am in reply to: Beko DVC 61W/1 fan oven element #157319

Simon46
Participant

Re: Beko DVC 61W/1 fan oven element

Thanks Dave 😀

S.

December 9, 2005 at 11:42 am in reply to: Zanussi FLA 1201W motor price #157236

Simon46
Participant

Re: Zanussi FLA 1201W motor price

Yes Masterpart just over £140 + vat.

S.

December 8, 2005 at 9:36 pm in reply to: Zanussi FLA 1201W motor price #157231

Simon46
Participant

Re: Zanussi FLA 1201W motor price

😯

Thanks Chris

December 8, 2005 at 12:40 am in reply to: Microwave for disabled lady #157082

Simon46
Participant

Re: Microwave for disabled lady

Thanks Don cant see one but it is a start. Will see if they know of one.

Regards
Simon.

December 2, 2005 at 8:37 am in reply to: washer sounds like a banshee #156439

Simon46
Participant

Re: washer sounds like a banshee

Also remove belt to prove motor bearings/drum bearing fault. Unplug power before checking :zap: .

Regards
Simon.
Author

Posts

Viewing 15 posts - 1,756 through 1,770 (of 2,216 total)

← 1 2 3 … 117 118 119 … 146 147 148 →