Simon46

Forum Replies Created

Viewing 15 posts - 1,816 through 1,830 (of 2,216 total)
1 2 3 … 121 122 123 … 146 147 148
  • Author
    Posts
  • October 31, 2005 at 7:46 am in reply to: Smeg A2 ‘Opera’ Cooker 100cm #152324
    Simon46
    Participant

    Re: Smeg A2 ‘Opera’ Cooker 100cm

    It is possible that the stat may be out of calibration. An oven thermometer will confirm this. Check out Repairs@ for an engineer in your area.

    Regards
    Simon.

    October 31, 2005 at 7:10 am in reply to: Smeg A2 ‘Opera’ Cooker 100cm #152322
    Simon46
    Participant

    Re: Smeg A2 ‘Opera’ Cooker 100cm

    Does the red light ever go out to say the oven has reached temperature?

    Regards
    Simon.

    October 28, 2005 at 1:43 pm in reply to: Bosch SGS5312GB/13 Dishwasher module #152069
    Simon46
    Participant

    Re: Bosch SGS5312GB/13 Dishwasher module

    Yes repair yours only. What i am after is an exchange module for my kit.

    Regards
    S.

    October 28, 2005 at 8:01 am in reply to: Bosch SGS5312GB/13 Dishwasher module #152067
    Simon46
    Participant

    Re: Bosch SGS5312GB/13 Dishwasher module

    Thanks Martin have done.
    Will wait and see.

    S.

    October 28, 2005 at 7:39 am in reply to: Bosch SGS5312GB/13 Dishwasher module #152065
    Simon46
    Participant

    Re: Bosch SGS5312GB/13 Dishwasher module

    Can you get me one please?

    S.

    October 27, 2005 at 8:38 pm in reply to: Hoover HCA 390FFK #152051
    Simon46
    Participant

    Re: Hoover HCA 390FFK

    BobHope is an expert on these. If the module fails it will run continuously So the freezer food is not lost. Have a look at it. I have had modules of QER for this problem.

    Regards
    Simon.

    October 27, 2005 at 5:11 pm in reply to: Indesit W143SUK. Coin in pump. Now no fill #151986
    Simon46
    Participant

    Re: Indesit W143SUK. Coin in pump. Now no fill

    Ah send to EMW No fault found. Open up every edge connector so it is a tight fit on board now works. Not logical. Perhaps it dried out in the post?

    S.

    October 25, 2005 at 8:39 pm in reply to: Zanussi FJ1093 Fills slowly! #149993
    Simon46
    Participant

    Re: Zanussi FJ1093 Fills slowly!

    Have you got selfbore taps clamped onto the pipes feeding the cold water to the machine?

    Regards
    Simon

    October 25, 2005 at 8:43 am in reply to: Electrolux EOB2610W pattern element #151656
    Simon46
    Participant

    Re: Electrolux EOB2610W pattern element

    Thanks Dave

    S.

    October 24, 2005 at 3:05 pm in reply to: I GIVE UP!!!!!!!! #151435
    Simon46
    Participant

    Re: I GIVE UP!!!!!!!!

    Thanks for ideas guys and Pat i hope it goes well for you!

    S.

    October 23, 2005 at 11:36 pm in reply to: I GIVE UP!!!!!!!! #151431
    Simon46
    Participant

    Re: I GIVE UP!!!!!!!!

    Chris what do you mean by detective agency?

    S.

    October 23, 2005 at 11:20 pm in reply to: I GIVE UP!!!!!!!! #151429
    Simon46
    Participant

    Re: I GIVE UP!!!!!!!!

    Just made that mistake. Had a cheque refer to drawer letter for Ariston fan oven motor. Mercedes parked in drive newbuild house but for sale sign. late for next job did not take details. Got mobile number only so am scuppered and will not answer. Left message wont reply. That’ll teach me!

    S.

    October 19, 2005 at 6:31 am in reply to: Indesit DG6145 Heater problem #150830
    Simon46
    Participant

    Re: Indesit DG6145 Heater problem

    There will be a safety stat that will cut the element out at 85 degrees. I would just have the element replaced. Unplug power if you are going to have a look yourself :zap: Or Try Repairs@ for an engineer in your area.

    Regards
    Simon

    October 19, 2005 at 6:22 am in reply to: Schreiber Fridge APM 6321 #150879
    Simon46
    Participant

    Re: Schreiber Fridge APM 6321

    Common these days is to replace the whole door with the seal on it as the door is built with the seal. If you look between the seal and doorand see some tiny screws holding the inner liner to the outer door then it is replacable. Dave Conway will enlighten you further shortly as to a price.

    Regards
    Simon.

    October 18, 2005 at 9:06 pm in reply to: Indesit DG6145 Heater problem #150828
    Simon46
    Participant

    Re: Indesit DG6145 Heater problem

    The appliance relies on the spray arms pumping water around the dishwasher. If this was working before it went pop then it should be a simple heater failure. Are you in hard water area/using salt?

    Regards
    Simon

  • Author
    Posts
Viewing 15 posts - 1,816 through 1,830 (of 2,216 total)
1 2 3 … 121 122 123 … 146 147 148