slyp98

Forum Replies Created

Viewing 15 posts - 136 through 150 (of 685 total)
  • Author
    Posts
  • in reply to: electrolux undercounter freezer wont start #435797
    slyp98
    Participant

    Re: electrolux undercounter freezer wont start

    Very good thanks

    in reply to: electrolux undercounter freezer wont start #435795
    slyp98
    Participant

    Re: electrolux undercounter freezer wont start

    Mumbo jumbo to me pal , I thought electrolyte was a substance diluted like in a battery , mop capacitors I take it are in the pcb

    in reply to: rsh1 dbbp no input from display buttons #434772
    slyp98
    Participant

    Re: rsh1 dbbp no input from display buttons

    Hi Richard it’s not diagnostic mode sorry I’ve just checked the rs21 manual , its load operation check function it just blinks all the lights off when power freeze and vacation are pressed its only when fridge temp is presses straight away does it gi to load operation

    in reply to: rsh1 dbbp no input from display buttons #434770
    slyp98
    Participant

    Re: rsh1 dbbp no input from display buttons

    from one of the components ? could it be a main board fault ?

    in reply to: bosch tuble dryer with condensor led on display #434281
    slyp98
    Participant

    Re: bosch tuble dryer with condensor led on display

    Yeah that’s the one no element just a big fridge compressor like heat exchanger , I did that mate used hot water , I read somewhere vinegar could be used to clean it out

    in reply to: bosch tuble dryer with condensor led on display #434279
    slyp98
    Participant

    Re: bosch tuble dryer with condensor led on display

    checked Dave looks fine , i havent had a call back so i take it all is well thanks kieran

    in reply to: bosch tuble dryer with condensor led on display #434277
    slyp98
    Participant

    Re: bosch tuble dryer with condensor led on display

    I tried it on all programs , had 2,very damp towels in there

    in reply to: electrolux esl 6114 wont fill #434239
    slyp98
    Participant

    Re: electrolux esl 6114 wont fill

    yeah Seamy , when i blew back into the hose that connects to the diaphram on the solenoid it had water behind i could hear the bubbling , does this mean theres a problem with the iwms /matrix , there are 2 other solenoids in the bottom of the iwms , they were buzzing away

    in reply to: electrolux esl 6114 wont fill #434237
    slyp98
    Participant

    Re: electrolux esl 6114 wont fill

    ok i found some info here about the iwms , this one looks ok but i didnt see the hoses behind the kickplate they could be gunged up

    in reply to: Dedietrich DOD448XG1 low temperature #433092
    slyp98
    Participant

    Re: Dedietrich DOD448XG1 low temperature

    cheers blackandwhites do you think this would cause the above fault , i dont want to find out it needs a new pcb instead, are there any values for the resistance of the probe

    in reply to: zanussi td4112w low heat #433905
    slyp98
    Participant

    Re: zanussi td4112w low heat

    anyone know where to access this stat or where its located cheersss

    in reply to: zanussi td4112w low heat #433904
    slyp98
    Participant

    Re: zanussi td4112w low heat

    Ah well this could be the problem so

    in reply to: zanussi td4112w low heat #433902
    slyp98
    Participant

    Re: zanussi td4112w low heat

    Yeah I tested them both have continuity so power is going through is there an exhaust air stat

    in reply to: Dedietrich DOD448XG1 low temperature #433090
    slyp98
    Participant

    Re: Dedietrich DOD448XG1 low temperature

    anyone ?

    in reply to: Dedietrich DOD448XG1 low temperature #433089
    slyp98
    Participant

    Re: Dedietrich DOD448XG1 low temperature

    Bump

    Sent from my HTC One mini 2 using Tapatalk

Viewing 15 posts - 136 through 150 (of 685 total)