stevebunyan

Forum Replies Created

Viewing 15 posts - 271 through 285 (of 305 total)
  • Author
    Posts
  • in reply to: Bosch Exxcel Dishwasher Serial Number #370865
    stevebunyan
    Participant

    Bosch Exxcel Dishwasher Serial Number

    Have you looked on the stainless steel of the door side or top. Etched in.


    Sent from Steves
    iPhone using Tapatalk

    in reply to: a quiet few days #370896
    stevebunyan
    Participant

    a quiet few days

    Last week very busy, today not to bad rest of week quite. But that’s how it is for line of work. Tomorrow is only a phone call away.
    Has any one done year on year stats, are there any trends that are seen year on year?


    Sent from Steves
    iPhone using Tapatalk

    in reply to: Neff S5443X2GB/42 bootom sprayarm not turning #370805
    stevebunyan
    Participant

    Neff S5443X2GB/42 bootom sprayarm not turning

    Have you checked the jets are clear?
    If there is pressure to the other spray arm and jets are clear and the machine isn’t being used on a half load wash. Then will most likely be the motorised valve motor.


    Sent from Steves
    iPhone using Tapatalk

    in reply to: Siemans XLM 1200 washing machine. #370782
    stevebunyan
    Participant

    Siemans XLM 1200 washing machine.

    Might be worth checking the heater and thermistors resistances.


    Sent from Steves
    iPhone using Tapatalk

    in reply to: Table top dishwasher #370761
    stevebunyan
    Participant

    Table top dishwasher

    Yep that’s the one.


    Sent from Steves
    iPhone using Tapatalk

    in reply to: Table top dishwasher #370759
    stevebunyan
    Participant

    Table top dishwasher

    I went to a customer who had a table top she bought from Argos (a Bush I think) she had the fill attached to her tap with a hose pipe connector do she could disconnect when not in use and the drain pipe dropped into sink when not in use. Not ideal but it worked for her.


    Sent from Steves
    iPhone using Tapatalk

    in reply to: DAMAGE WAIVER FORM #370754
    stevebunyan
    Participant

    DAMAGE WAIVER FORM

    I had this in a student flat. I went straight to the letting agent, explained that I noticed a mark after I had worked on the washer but didn’t think I caused it but the students where insisting that I had. They where good about it and said at the end of there tenancy they where allowed an amount of wear and tear. Never heard any more. Now I use a big bath towel to put under the washer on vinyl floor.


    Sent from Steves
    iPhone using Tapatalk

    in reply to: Indesit w133 door seal removal #370649
    stevebunyan
    Participant

    Indesit w133 door seal removal

    I got my bent long nosed pliers from eBay for about £6.00 used them loads


    Sent from Steves
    iPhone using Tapatalk

    in reply to: Unreal prices. #370415
    stevebunyan
    Participant

    Unreal prices.

    This has been an on going problem for years. I managed a kitchen show room some years ago and we where always coming up against the Internet price cutters. The trouble is they are buying at the same price or better than the wholesalers and relying on quantities. Some manufactures won’t allow there products to be sold in that way so we stuck with them. At that time Neff was ok to deal with.


    Sent from Steves
    iPhone using Tapatalk

    in reply to: Indesit w133 door seal removal #370645
    stevebunyan
    Participant

    Indesit w133 door seal removal

    That’s embarrassing I have just done 2 machines and would have swan they where Indesit. I really must get this new glasses or my memory checked.


    Sent from Steves
    iPhone using Tapatalk

    in reply to: zanussi ZDC46130W condenser drier dead #370523
    stevebunyan
    Participant

    zanussi ZDC46130W condenser drier dead

    Is 240 coming out of door lock?


    Sent from Steves
    iPhone using Tapatalk

    in reply to: Candy S95 Oven door wont stay closed #358089
    stevebunyan
    Participant

    Candy S95 Oven door wont stay closed

    When you open the door. Look at where the hinge enters the oven, you will see a silver plate covering the hinge, flick these up and back as far as they will go, then slowly close the door until the door touches them, this will now allow to to lift the door and slide away from the oven. Once the door is removed you can remove the hinges from the door.

    Sent from Steves
    iPhone using Tapatalk

    in reply to: Indesit w133 door seal removal #370639
    stevebunyan
    Participant

    Indesit w133 door seal removal

    If you remove the plastic panel with the knobs at the top and also the plastic plinth at the bottom which slides left once the screws at filter are removed, you will see 4 screws, 2 top 2 bottom, remove these and the frt will slide down and off.


    Sent from Steves
    iPhone using Tapatalk

    in reply to: collecting your call out #370448
    stevebunyan
    Participant

    collecting your call out

    I agree, and find charging a fee sorts out the dross, I charge a few that I will knock off the repair cost, that way if they don’t go ahead I have at least covered my costs.


    Sent from Steves
    iPhone using Tapatalk

    in reply to: zanussi ZDC46130W condenser drier dead #370521
    stevebunyan
    Participant

    zanussi ZDC46130W condenser drier dead

    Have you measured the voltage?


    Sent from Steves
    iPhone using Tapatalk

Viewing 15 posts - 271 through 285 (of 305 total)