Steven

Forum Replies Created

Viewing 15 posts - 691 through 705 (of 786 total)
1 2 3 … 46 47 48 … 51 52 53
  • Author
    Posts
  • February 13, 2008 at 9:36 am in reply to: Ignis D/w no heat #243060
    Steven
    Participant

    Re: Ignis D/w no heat

    Cheers John

    I have sent him back to take another look, and while he was there this time the machine did error out as though there wasnt enough water.
    He reset it and it filled ok, so it could be an intermittant flow meter fault.

    Initially the level and the circulation action seemed ok but i did ask him about the water level.

    I got him to top it up manually while it was in a cycle, but if the board has already detected low water level then by doing this probably would not have made much difference is this right?

    Will change flow meter and see what happens.

    Steven

    February 12, 2008 at 1:51 pm in reply to: Ignis D/w no heat #243057
    Steven
    Participant

    Re: Ignis D/w no heat

    I have not looked at it myself, this is on behalf of my engineer.

    But he has said that he has tested the mains supply directly from the terminals of the large pcb in the base and it has no voltage from the relays.
    Where do these relays get there supply from is it on the main pcb itself?

    Could it be a faulty pcb? It has been repaired by emw.

    I dont think There are many wires in the door on this type.?

    Steven

    February 11, 2008 at 3:19 pm in reply to: Business/Van Insurance #240558
    Steven
    Participant

    Re: Business/Van Insurance

    Ken

    I will be interested, ours runs out in march so need to start looking round for shop and liability insurance.

    If you have details let me know.

    February 8, 2008 at 2:21 pm in reply to: IND W/D WIDL126 #242610
    Steven
    Participant

    Re: IND W/D WIDL126

    cheers Martin

    My engineer has checked the condenser all clear, the machine is just over 12mths old, customer has been doing the same program since he has lived there. (rented property) and has had no problems before (or so he said, you know what its like customers never tell you the whole story)
    especially if you mention overloading or too much detergent.

    Surely if it was overheating it would still error out, you know what Indisits are like slightest fault.

    Steven

    February 4, 2008 at 12:31 pm in reply to: HPT DWF34 D/W mains filter #242146
    Steven
    Participant

    Re: HPT DWF34 D/W mains filter

    Dont worry invoice in post to him today.

    February 4, 2008 at 12:12 pm in reply to: HPT DWF34 D/W mains filter #242144
    Steven
    Participant

    Re: HPT DWF34 D/W mains filter

    So there is no legal requirement to use it without one i assume?

    January 31, 2008 at 5:14 pm in reply to: Van signwriting #241492
    Steven
    Participant

    Re: Van signwriting

    Ken

    I am sure i have signed up, but you better check ❗

    Steven

    January 31, 2008 at 10:26 am in reply to: Van signwriting #241489
    Steven
    Participant

    Re: Van signwriting

    I am sure it ok to use if required ISE and ukwhitegoods logos.
    Am i right Ken ❓
    Steven

    January 25, 2008 at 12:35 pm in reply to: Beko WMB10W on off switch #241045
    Steven
    Participant

    Re: Beko WMB10W on off switch

    on/off switch BEK2201920500

    Steven

    January 18, 2008 at 5:16 pm in reply to: Samsung RS21DCNS #239858
    Steven
    Participant

    Re: Samsung RS21DCNS

    I have looked up the part numbers for both sides, they appear to be same numbers is the correct?

    January 18, 2008 at 5:14 pm in reply to: Samsung RS21DCNS #239857
    Steven
    Participant

    Re: Samsung RS21DCNS

    Yes done the test mode not showing a fault.

    Thanks for all your advice, really appreciated.
    I will pop back and replace the sensors see how things go.

    Regards
    Steven

    January 17, 2008 at 2:20 pm in reply to: Samsung RS21DCNS #239849
    Steven
    Participant

    Re: Samsung RS21DCNS

    How can the fridge be the problem when the fridge is holding correct temperature, and the freezer not.?
    When they have two seperate evaporators.

    Regards
    Steven

    December 13, 2007 at 9:42 am in reply to: Beko Wma1715s #236933
    Steven
    Participant

    Re: Beko Wma1715s

    Cheers Chris


    I did try and search for this as i thought it would be in there some where, but cant seem to use this facility properly.

    Steven

    December 12, 2007 at 10:47 am in reply to: Beko Wma1715s #236931
    Steven
    Participant

    Re: Beko Wma1715s

    Just checked with engineer.

    Cannot cancel or remove this error, tried disconnecting appliance, etc.
    As I cannot remove this, the washer wont work at all.
    Seems to be locked out, any idea how to unlock it?

    Steven

    November 30, 2007 at 9:55 am in reply to: HPT WD440 W/Dryer #235755
    Steven
    Participant

    Re: HPT WD440 W/Dryer

    It was a rented property and customer was not there at time just the landlord, who gone back to London. I have now talked her throu it, she had not read the instructions properly :rolls:

    All ok now.

    Steven

  • Author
    Posts
Viewing 15 posts - 691 through 705 (of 786 total)
1 2 3 … 46 47 48 … 51 52 53