[Steven]

Re: Introduction of Iris Codes

TBH dont get too technical, if its a motor related fault then just put

611- no motor rotation
or 621 irregular rotation this should cover! 😉

Have you got the excel symptom code sheet?

If not let me have your email I send you the copy?

Steven

[Steven]

Re: February 2012

Hi Guys

yep just cc you an email to let you know?

Have you had a reply from statesman?

I will again chase up, daewoo giving them cut off date if we havent had a response by 3 Feb then assume they do not want a stand.

[Steven]

Re: Pre Feb Mtg 2012

Forget that one then :boops:
Would you still like to invite him :stir:

[Steven]

Re: Pre Feb Mtg 2012

Lawrence wrote:😀 Ok an attempt to download my Brain for the 27th

Stephen – Front of house -Meet & Greet – what do you need ?

LAC

A new suit and a couple of sexy birds for starters! 😆

I think Bryan has the pull ups!!

In regards to PA cant we get in touch direct with the ones that do the hotel any way and hire?

Do we want to ask any one else if they would like to pop along as back up in case some drop out!

I have another meter company i could approach and also have you heard of ELEMENTMAN, we have used this company a few times if you get obscure or obsolete parts he can make em up!!

Steven

[Steven]

Re: February 2012

Just sent email reminding those to let us know as soon as possible.

Steven

[Steven]

Re: February 2012

Dales-Electronic wrote:Steven,

Statesman, Swift and Daewoo for stands ??

Ian

I take it this is a question and you have not had a reply from them?

Would you like me to follow up?

Steven

[Steven]

Re: February 2012

Hi all,

Are we going to get done the banners/posters or table cloths with company logos on to place around the room?

Have we a plan of the room so we can get the layout and positions of stands down on paper and put on web site, so everyone knows where they will be sited?

Steven

[Steven]

Re: Creda T/dryer lid problem

Martin wrote::hmm: Not sure exactly where you suggest the screwdriver be placed wilf TBH but I will give it a go, thanks. IIRC like with most Indecrap, the lid removes backwards to release from the fascia, so bashing it forwards is a no no?

With other t/d’s a w/m’s, I’ve just removed the 2 rear screws, lifted the lid slightly at the back then thumped them with the ball of the hand at the front to release. However this SOAB won’t comply to convention……….. 👿

Screw driver works well, used to whack it with palm but after a while it can hurt.

You place the large flat screwdriver behind the flat of the tab and lever! It wont snap honestly 😉

Steven

[Steven]

Re: Pre Feb Mtg 2012

I have text Barrie and he is happy to carry on printing the certificates from his printer, he has done most already.

then he bring them along for us to post off.

Steven

[Steven]

Re: Pre Feb Mtg 2012

Whats the plan so far?

Have we all the replies from Ian on whos coming etc.

If not then we need to chase up these people up.

We also need the folders and paper work from Baz so certificates and letters can be done and get them posted out ASAP.

Has UKW got a laser printer, we can use?

Steven

[Steven]

Pre Feb Mtg 2012

I don’t think I can make it?
Boss is off, and i have family comittment at the weekend!
Will be available by Skype or email if required.

[Steven]

Re: Van Insurence

Try CVD
Commercial vehicle Direct
http://www.cvd-insurance.co.uk/Commerci … tAodEnarWA

I have tried all the compare sites and this one always cheaper!
been with them for the past 9 years for both our vans.

My due middle of January so will be getting quote soon!

Always do get quotes but as with all insurance companies they are so desprate for business you still haggle!!

Dont always accept the renewal quote!!

This includes fully comp, breakdown, ncp, legal.
Also includes a under 25 as well on the policy.
addtional if you want it key care and gap insurance!

Steven

[Steven]

Re: ise 10 Leak

Thanks Tim, Had a read and similar to jonnyhoz fault!

But had a good look around and no trace of leaks at all no obvious water marks which if it was soapy you should see!

my guy went there before and replaced thermister the cradle was dry!
This time as the fault has re appeared with exact same symptoms, so found it now wet, so suspect that it dried out before we got there previously!

He took several photos although does not help, it does show that it has been leaking for some time, rust spots in the base, motor has traces of rust patches all over so definatly a leak coming from higher up!

Dried out thermiser which is why the board was going loopy and prevented it being reset etc.
Still not working properly?

He checked the dispenser hose and removed it, it was all bone dry, no signs of any dampness!!
Will have to take longer more thorough look or just seal up dispenser?

Steven

[Steven]

Re: *** Feb Whitegoods Conference ***

You can bring the WAGS if you like:lol:

There is a Spa and Gym if you stay over to make use of and dare say they could still use it if not, or they can indulge in a bit of shopping!

Depends whether they are interested in the appliances, drinking sessions and dirty weekend away 😉

Steven

[Steven]

Re: Daewoo appliances warranty ?

garn wrote:Steve said

One customer refused repair and has had an exchange and purchased a different brand!

Hope not A customer Refused a 2nd repair On a Amica I exchanged a Amica For a daewoo 🙁

garn

:rotl: :rotl:

Funny enough just had a email from Adam! Long story so I will try and keep it short. 😆

I requested a service call via email for the visit under warranty no number given, when I called they said you need to phone! :rolls:
Why when all the info is in an email easy, and its recorded!
Reply back today was you can log by phone or email :haier:
Thats what i did!!

Now they said only going to pay for one visit!

Emailed right back with no friggin way!.

They either pay up or its BYE BYE!! No more daewoo if thats how they want to play it, I dont need the hassle !

Steven

[Author]

Posts