timdowning

Forum Replies Created

Viewing 15 posts - 301 through 315 (of 2,180 total)
  • Author
    Posts
  • in reply to: Whirlpool to do a recall on Hotpoint dryers #431471
    timdowning
    Participant

    Re: Whirlpool to do a recall on Hotpoint dryers

    So as previously discussed the overheat stat isn’t doing its job…

    in reply to: ZWD14270W1 #436982
    timdowning
    Participant

    Re: ZWD14270W1

    It will be the main one. The smaller one is the dryer control.

    in reply to: Carbon brush wear #436919
    timdowning
    Participant

    Re: Carbon brush wear

    It’s definitely on the 1600 spin hoover models with the dc module at the bottom. Had another one this week. 5 years old. One brush completely gone the other as good as new.

    in reply to: Re Hotpoint DSC60S Stand Alone Cooker #436881
    timdowning
    Participant

    Re: Re Hotpoint DSC60S Stand Alone Cooker

    If all that’s ok then it could be the timer itself. Can you bypass it to prove the point?

    in reply to: Neff V6320X0GB/01 dryer problem #436690
    timdowning
    Participant

    Re: Neff V6320X0GB/01 dryer problem

    I wouldn’t have thought the valve not operating would cause the overheat to operate.
    Are you sure the condensers not blocked & the fan is fluff free…

    in reply to: Washing machine Return rights #436290
    timdowning
    Participant

    Re: Washing machine Return rights

    Putting 1 item in will be an ‘out of balance’ load on any machine. Hence the not spinning.
    Are you sure you are choosing the right program for the correct spin?
    What is the max spin of your machine compared to your old one. Don’t forget quick washes often door a lower spin than a cottons even if a spin dial is set to max.

    in reply to: Any Recommends Re Decents Dishwashers… #436166
    timdowning
    Participant

    Re: Any Recommends Re Decents Dishwashers…

    I sell a lot of Bosch & still find them better than other makes.
    http://www.bosch-home.co.uk/products/di … width.html
    For £450 you will get pretty high up in the range.

    in reply to: Any Recommends Re Decents Dishwashers… #436164
    timdowning
    Participant

    Re: Any Recommends Re Decents Dishwashers…

    Freestanding or integrated?

    in reply to: Whirlpool to do a recall on Hotpoint dryers #431406
    timdowning
    Participant

    Re: Whirlpool to do a recall on Hotpoint dryers

    You can keep going with this;
    what if you fit a pattern kit whose tolerances are higher than the original stat kit.
    So resetting the original overheat may be safer than a new pattern kit…

    in reply to: Whirlpool to do a recall on Hotpoint dryers #431391
    timdowning
    Participant

    Re: Whirlpool to do a recall on Hotpoint dryers

    It certainly wasn’t lint, I cleaned it out three weeks earlier as a precaution…
    (Proper strip down & drum away from backplate clean out)
    As I say, I think it’s an overheat issue, certainly on this one. No dryer should get that hot that the contents combust.

    in reply to: Whirlpool to do a recall on Hotpoint dryers #431389
    timdowning
    Participant

    Re: Whirlpool to do a recall on Hotpoint dryers

    It was the contents that caught fire.
    All components were spotless, there certainly wasn’t any fluff build up.
    Could it be just that they overheat due to the overheat stat not operating soon enough?
    I’ve been to many a Hotpoint where the belt has gone or the starter capacitor has failed but the heater is still cooking away merrily…

    in reply to: Whirlpool to do a recall on Hotpoint dryers #431384
    timdowning
    Participant

    Re: Whirlpool to do a recall on Hotpoint dryers

    Talk us through it Tim, but you AND the Fire Brigade called out to the same dryer fire?

    The dryer caught fire, the fire brigade were called, I went out to inspect it,then dispose of it & put a new dryer in.

    in reply to: Whirlpool to do a recall on Hotpoint dryers #431374
    timdowning
    Participant

    Re: Whirlpool to do a recall on Hotpoint dryers

    I went to one last week, luckily the fire brigade got there in time. Thank goodness they had working smoke alarms!!

    in reply to: How to deal with musophobia (fear of mice) #435971
    timdowning
    Participant

    Re: How to deal with musophobia (fear of mice)

    Your eyes must be frozen Jim, its a washing machine!!

    in reply to: just when you think you had seen it all !! #435939
    timdowning
    Participant

    Re: just when you think you had seen it all !!

    I reckon it was left there and blocked up at the front when they had the kitchen last done.

Viewing 15 posts - 301 through 315 (of 2,180 total)