Tubs

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 179 total)
1 2 3 4 … 10 11 12
  • Author
    Posts
  • March 12, 2010 at 12:23 pm in reply to: AEG favorit 86070VI dishwasher #314522
    Tubs
    Participant

    Re: AEG favorit 86070VI dishwasher

    Thanks penguin

    Did suspect water level was a tad too low, same as the Bosch I guess, funny thing is they say it wahses a treat 😕

    Steve

    March 10, 2010 at 4:58 pm in reply to: AEG favorit 86070VI dishwasher #314519
    Tubs
    Participant

    Re: AEG favorit 86070VI dishwasher

    Pnc

    911937608

    Steve

    November 4, 2009 at 12:42 pm in reply to: Jackson 28216 combi oven/microwave #302487
    Tubs
    Participant

    Re: Jackson 28216 combi oven/microwave

    Thanks Chris

    Steve

    July 30, 2009 at 3:54 pm in reply to: Bosch WFL2463gb/12 #293492
    Tubs
    Participant

    Re: Bosch WFL2463gb/12

    Thanks Martin

    Seems to be the only logical thing I can also think of, Typical, does not do it when you’re there!

    Steve

    July 30, 2009 at 9:33 am in reply to: T/Bendix WDR 1041 stops. #293493
    Tubs
    Participant

    Re: T/Bendix WDR 1041 stops.

    Have you checked heater for low insulation ?

    Sometimes throws up error for ‘no drain’ fault

    Steve

    March 11, 2009 at 4:51 pm in reply to: Zan E40 not interlock #279089
    Tubs
    Participant

    Re: Zan E40 not interlock

    Steven wrote:Possible one of the pumps shorted out,usually the recirc, this can damage the triacs on the pcb. You say you have changed the pcb, check the individual triacs you may see one with a chip out of it, trace it back to the relevant pump.
    You may have have damaged the new board.

    Hope this helps

    Steven

    Have also had this and was re circ pump melted, had me scratching head for a while.

    March 11, 2009 at 4:38 pm in reply to: Rangemaster 110 #279910
    Tubs
    Participant

    Re: Rangemaster 110

    Tops have to come off (one side slides forward and one side slides to the right, if I remember) Remove the vent slat metalwork along the back first.
    These have to be removed to gain access to top screws that hold front panel on.

    Think sides have to be removed also (been a while since i’ve repaired one)

    Steve

    January 14, 2009 at 5:00 pm in reply to: Whirlpool H Duty T/Dryer #274008
    Tubs
    Participant

    Re: Whirlpool H Duty T/Dryer

    wilf wrote:take a small socket set with you. I fitted stats to one of these and found the fixing bolts to be an odd size.

    wilf

    Think you will find 2ba and 4ba sockets on these most helpful.

    November 21, 2008 at 5:08 pm in reply to: whirlpool american t/d leq8033 #269157
    Tubs
    Participant

    Re: whirlpool american t/d leq8033

    Will do some research for you, have one of these at home but never use sensor dry.

    November 21, 2008 at 1:12 pm in reply to: Atag freezer DGA 6035u/AO #269155
    Tubs
    Participant

    Re: Atag freezer DGA 6035u/AO

    Thanks Bazza,

    looks like from your avatar you could be a fellow diver?
    Steve

    November 20, 2008 at 4:46 pm in reply to: Zanussi DE6544 D/W fault guide. #269060
    Tubs
    Participant

    Re: Zanussi DE6544 D/W fault guide.

    Think you will find it’s a water fill time out (pressure switch does not switch to full within 4 mins) check all the usual.

    Steve

    October 31, 2008 at 5:41 pm in reply to: Whirlpool top loader no motor drive. #266464
    Tubs
    Participant

    Re: Whirlpool top loader no motor drive.

    Hi, hope this link helps,

    http://ukwhitegoods.co.uk/modules.php?n … 92de3c5fa1


    Steve

    October 28, 2008 at 3:52 pm in reply to: AEG Lavamat L16810 Washer/ Drier “No heat from drier&qu #266778
    Tubs
    Participant

    Re: AEG Lavamat L16810 Washer/ Drier “No heat from drie

    Hi

    Check two flimsy blue wires to stat, have had same fault but loom wire oc.

    Steve

    October 28, 2008 at 3:42 pm in reply to: WHIRLPOOL AMERICAN WASHING MACHINE – 3RGSC9455JQ – DEAD #266821
    Tubs
    Participant

    Re: WHIRLPOOL AMERICAN WASHING MACHINE – 3RGSC9455JQ – DEAD

    If its the one with the “pull for on” type then have had this being timer before.

    Steve

    October 21, 2008 at 4:20 pm in reply to: servis/hygena apm8513/2 #265944
    Tubs
    Participant

    Re: service/hygena apm8513/2

    Module, had two of these this week with same fault as you describe. Check rating plate for details as few different variations on module, Connect list them but expensive pt no. 546021400

    Steve

  • Author
    Posts
Viewing 15 posts - 31 through 45 (of 179 total)
1 2 3 4 … 10 11 12