[Tubs]

Re: American Whirlpool Drier ‘Dead’

Hi all,

Always been the thermal fuse on the ones ive repaired for fault description “dead”.

Steve

[Tubs]

Re: AEG pnc no. 914001216

Thanks dave

Much appreciated :tup:

Steve

[Tubs]

Re: 16th Edition

Hi all

I have an interesting article on light bulbs, I will see if I can dig it out

Steve

[Tubs]

Re: Hoover AM120 Washing Mc

Hi

Thanks Andy,

yer sounds like the similar sort of fault that we get on the wma Hotpoint range with open circuit tacho coil, couple of spins then nothing.

You know what these customers descriptions are like over the phone.

Thanks mate

Steve :wave:

[Tubs]

Re: Advice sought to repair cooker module Electrolux EPSOPMS

Hi there,

Its the VA rating of the secondary winding that matters. dont see it to be too much of a problem as you are supplying a 5v regulator (which if memory serves me correct needs a minimum of 7v supply).

At 9 volts you would need a current rating of .35 amps, in order to give you the same VA rating.

Hope this helps

Steve

[Tubs]

Re: Trading standards

Thanks Martin,

Just what I was after :tup:

Steve

[Tubs]

Re: Hotpoint B/I double oven BD81, light coming on?

Hi Guys

Thanks for the input.

Oven all works ok, light comes on when it should (when regulators are turned etc) just decides to fire up flo tube when cooling fan cuts in. As you know could be a couple of minutes after ovens are turned off. Unit appears not to have trigger board (partfinder Cd).

Will post outcome, back there next week armed with selector switch ❗

Steve

[Tubs]

Re: Hotpoint B/I double oven BD81, light coming on?

Hi seamy, my thoughts exactly. Does seem to imply that the selector switch has welded itself together on the selector switch side, so of course the light would come on anyway when the selector switch is turned. Must be getting a feed when toc cuts in when cavity gets too hot.

If the light does come on with fan its the first ive ever seen. Looks like i have no choice but to pull it all out 😥

Thanks Steve

[Tubs]

Re: AEG Dishwasher. F507601M. PNC 911 234 716 00

Hi Chris

Heating relay pt no. is 899669808049/7

Cant remember location, but hope this helps

Steve

[Tubs]

Re: WMA 33

Hi Lee

Check tacho coil

Steve

[Tubs]

Re: Tales From The Front Lines

Hi all

Went to a rental customer a couple of months ago, Bendix washer/dryer. Customer complaining of machine flooded kitchen floor, followed by earbashing that our machines caused all this damage.

Done the usual checks, no split hoses, backing up waste etc. Then I decided to pull out soap drawer. What a suprise, because it was a washer dryer she decided to start using the Bounce freshener tissues and was putting them in the soap drawer ❗ must have been ten in there all screwed up. its a great job if it wasnt for the customers 😉

[Tubs]

Re: Zanussi ZD684w drain problem

Start with the pump, take it out & check all the blades are intact on the rear impellor.

With farmboy on this one, had this many a time

Steve

[Tubs]

Re: Holidays

See a later all,

Off to Morroco for a week, see how many camels I can get for the Mrs 😉 .

I expect plenty of reading when I get back :tup:

:wave:

Steve

[Tubs]

Re: samsung srs2026cvw american style f/f

Hi Pinky

Andy is right. If you hold down quick freeze & vacation button for eight secs the machine should go into self diagonstics. ( buzzer should ding dong, no not Leslie Philips) when mode is selected. Have you access to Service manual as I see you can access their website. PM if you need any more info.
Steve

[Tubs]

Re: What is the most useful tool in your toolbox?

Hi all

Just found this handy sized manual hand pump in the CPC catalouge for those big pump out water jobies.

Pt no. CPO1112 (its in the boat & caravan section) Have no pickie i’m afraid 😥

[Author]

Posts