Tubs

Forum Replies Created

Viewing 15 posts - 46 through 60 (of 179 total)
1 2 3 4 5 … 10 11 12
  • Author
    Posts
  • October 14, 2008 at 2:57 pm in reply to: Beko T/d #265140
    Tubs
    Participant

    Re: Beko T/d

    Quite agree

    pile of ****

    Changed pcb in one three months ago for same fault. Customer says is now doing same thing.

    Steve

    August 29, 2008 at 11:36 am in reply to: ZWF1427W DEAD #253345
    Tubs
    Participant

    Re: ZWF1427W DEAD

    Hi Guys,

    came accross exactley the same fault this morning, and yes changed pcb and door switch, still dead as a dodo. What was the outcome. Have volts in all the right places but still no power to pcb.

    Steve

    June 27, 2008 at 4:34 pm in reply to: Miele oven #256092
    Tubs
    Participant

    Re: Miele oven

    HI Steven,

    F5 Oven pt 1000 sensor short circuit.

    Steve

    June 19, 2008 at 1:54 pm in reply to: Hotpoint WMA 66 Ultima #255056
    Tubs
    Participant

    Re: Hotpoint WMA 66 Ultima

    Hi Iadom

    Have had this before (while back now), changing the board cured the fault, could not find any other underlying issues.

    Steve

    June 19, 2008 at 11:44 am in reply to: Zanussi ZWF1415w #254403
    Tubs
    Participant

    Re: Zanussi ZWF1415w

    Hi Guys

    Just an update for future ref, heater was low insulation.

    steve

    June 12, 2008 at 11:08 am in reply to: Zanussi FLE1215W Wash M/c – Neon Light Error Codes? #254458
    Tubs
    Participant

    Re: Zanussi FLE1215W Wash M/c – Neon Light Error Codes?

    Hi Laurence

    Have had this before, changing interlock cured it.

    Steve

    June 12, 2008 at 8:32 am in reply to: Zanussi ZWF1415w #254401
    Tubs
    Participant

    Re: Zanussi ZWF1415w

    Surely one of you guys have seen this before :rolls:

    Steve

    April 10, 2007 at 9:31 am in reply to: Beko dv5531g electric cooker #209809
    Tubs
    Participant

    Re: Beko dv5531g electric cooker

    I must be missing something 😕

    Circuit diagram shows wires comming from micro switch to grill and top element being separate (what I would expect to see) Only thing is cooker has only one top element wired as top oven element and grill with only L & N connections, not L,N (grill) and L,N for top oven element.
    Help. (lady had odd job man in to try and fix it and left wires off everwhere)

    Steve

    April 5, 2007 at 4:26 pm in reply to: Beko dv5531g electric cooker #209808
    Tubs
    Participant

    Re: Beko dv5531g electric cooker

    Thanks Bob, Had a look, couldnt see it. will have another peek a boo

    Thanks again
    steve

    February 1, 2007 at 4:21 pm in reply to: Hotpoint Mistral ff92p #202977
    Tubs
    Participant

    Re: Hotpoint Mistral ff92p

    Hi Subs,

    Have you checked thermal fuses for continuity (located at the back right hand side at rear of freezer compartment, should be two of them)

    Steve

    February 1, 2007 at 4:13 pm in reply to: Hotpoint wmm 65a 1600 ultima #201250
    Tubs
    Participant

    Re: Hotpoint wmm 65a 1600 ultima

    Me thinks so. If its anything like the WMA range chaffing motor loom, tends to take the board with it also.

    Steve

    January 31, 2007 at 1:40 pm in reply to: Wet Beavers #202862
    Tubs
    Participant

    Re: Wet Beavers

    Martin wrote:What with global warming and rising sea levels you’ll need scuba gear just to live in Kent…. 😆

    Must be controlled with an Indesit pressure stat surely

    January 31, 2007 at 1:26 pm in reply to: Wet Beavers #202860
    Tubs
    Participant

    Re: Wet Beavers

    Just for the record, beaver are a well known diving equipment manufacturer. What was you thinking of 😆 as us divers say a wet beaver is a happy beaver.

    Must be quite lucky living on the coast I suppose.

    Steve

    January 31, 2007 at 9:51 am in reply to: Getting the belt on the tension pulley – Hpt condenser dryer #132516
    Tubs
    Participant

    Re: Getting the belt on the tension pulley – Hpt condenser d

    PIP-pm- wrote:8″ long 1/4 inch drive socket shaft the 1/42 drive recieve end fits over the drive shaft and the belt slips on job done

    Thats exactly what I do, save yer pennies Martin

    January 31, 2007 at 9:45 am in reply to: Hotpoint wmm 65a 1600 ultima #201243
    Tubs
    Participant

    Re: Hotpoint wmm 65a 1600 ultima

    Last one I had turnd out to be chopper board. Fault description, no drum action

    Steve

  • Author
    Posts
Viewing 15 posts - 46 through 60 (of 179 total)
1 2 3 4 5 … 10 11 12