washermanuk

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 165 total)
1 2 3 … 9 10 11
  • Author
    Posts
  • September 15, 2011 at 9:35 pm in reply to: Miele G1270 Dishwasher F14 pulsing problem #358774
    washermanuk
    Participant

    Re: Miele G1270 Dishwasher F14 pulsing problem

    Hi matey had one doing the same? found plastic wrapper caught in the end of the circ pump!

    February 16, 2011 at 6:04 pm in reply to: MIELE W2240 #344840
    washermanuk
    Participant

    Re: MIELE W2240

    Hi did you check the condition of the carbon brushes?
    If the motor is at fault Miele cover the part for 10years but they must call and fit new motor 😥

    February 9, 2011 at 12:31 am in reply to: miele w919 #343902
    washermanuk
    Participant

    Re: miele w919

    If my memory serves me possible heating problem?
    Check HEATER,RELAY and NTC!
    hope this helps BRIAN

    February 8, 2011 at 6:41 pm in reply to: AWCT 101 DOOR FALLING OFF #343759
    washermanuk
    Participant

    Re: AWCT 101 DOOR FALLING OFF

    Hi Anne
    Think the powers that be from my office have already discussed about sending photos when job is completed and claim form is returned?
    For your reference it will be under http://www.electricalsales.co.uk/
    David Hothersall.
    Brian.

    February 7, 2011 at 7:23 pm in reply to: AWCT 101 DOOR FALLING OFF #343758
    washermanuk
    Participant

    Re: AWCT 101 DOOR FALLING OFF

    Ok anne see what i do 😉

    February 5, 2011 at 9:43 pm in reply to: AWCT12L orange fault code?? #343587
    washermanuk
    Participant

    Re: AWCT12L orange fault code??

    Hi strange thing i had a machine with the same fault AWCT10L
    ON/OFF went out ADD RINSE and SPIN leds on and START/PAUSE led turns red
    Found no power going to heater element
    Changed module wich cured the fault! must be a heater relay on pcb not switching on?
    Brian

    January 26, 2011 at 11:20 pm in reply to: new panasonic washing machine #342218
    washermanuk
    Participant

    Re: new panasonic washing machine

    Hope you recover asap matey all the best Brian!!
    just reminds everyone how dangerous our job is?
    😥

    January 20, 2011 at 11:51 pm in reply to: Bosch countdown… #341897
    washermanuk
    Participant

    Re: Bosch countdown…

    sorry takes me to log in page? 😥

    January 18, 2011 at 8:34 pm in reply to: UKWG addicts #341620
    washermanuk
    Participant

    Re: UKWG addicts

    The other half only wants you off the comp to play flipping bingo? :rolls:

    January 18, 2011 at 8:28 pm in reply to: test #341691
    washermanuk
    Participant

    Re: test

    I was just looking at that post but decided not to add didnt want to seem like an addict!!! :conf:

    January 18, 2011 at 8:22 pm in reply to: test #341689
    washermanuk
    Participant

    Re: test

    SHOULD THAT NOT BE TESTING TESTING 123? 😉

    January 18, 2011 at 8:13 pm in reply to: HOTPOINT F72PR MISTRAL #341610
    washermanuk
    Participant

    Re: HOTPOINT F72PR MISTRAL

    MANY THANKS LOOKS LIKE SUMONE BEEN MESSING :rolls:

    November 30, 2010 at 10:27 pm in reply to: Miele T650C Tumble Dryer #337341
    washermanuk
    Participant

    Re: Miele T650C Tumble Dryer

    condensor dryer check lower base fan for condensation very common in making these trip out! the fan onlt comes on after a few mins? either dry this out or replace if too far gone? check condensor box seals as this lets steam get onto this fan moter! hope this helps?
    Brian 😉

    November 14, 2010 at 12:04 am in reply to: Miele D/W G1530SC – noisey drying fan #335716
    washermanuk
    Participant

    Re: Miele D/W G1530SC – noisey drying fan

    Cooling fan is mounted on the lhs at the bottom not too bad to change!
    replaced a few due to noise 😥

    November 13, 2010 at 11:59 pm in reply to: Miele PW5065 Poor Spin Performance #335724
    washermanuk
    Participant

    Re: Miele PW5065 Poor Spin Performance

    No carbons on this and its a 3 phase motor but tacho is available as a seperate item
    pressure switch is built on the control pcb
    dont blow up the pipe to check if pressure switch works as this puts the calibration out 😥 not worked on any of these so cannot give you any more help regards Brian

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 165 total)
1 2 3 … 9 10 11