washermanuk

Forum Replies Created

Viewing 15 posts - 136 through 150 (of 165 total)
  • Author
    Posts
  • in reply to: miele W3722 GB #299191
    washermanuk
    Participant

    Re: miele W3722 GB

    Speed sensor fault

    in reply to: Dirty Gertie at number 30 #299172
    washermanuk
    Participant

    Re: Dirty Gertie from no 30

    That reminds me of the time i called to a vented dryer not heating!!
    went to check vent hose and jumped six foot in the air 😯 3 mice nesting in the hose amongst the fluff 😮 they ran out and went behind the fridge.
    Chap said “thats always happening” 😐

    in reply to: Dirty Gertie at number 30 #299170
    washermanuk
    Participant

    Re: Dirty Gertie from no 30

    Did you have a brew and a biccie? 😆

    in reply to: Miele W827 #299122
    washermanuk
    Participant

    Re: Miele W827

    Brush housing is available,sounds like the pcb board tho!!! :rolls:

    in reply to: Miele Novotronic T240 Air Vented T/D #298804
    washermanuk
    Participant

    Re: Miele Novotronic T240 Air Vented T/D

    Hi Matey it is the one above heater “Blue spot”
    Cause for this restricted air flow, filters etc

    in reply to: Zanussi E10 #299052
    washermanuk
    Participant

    Re: Zanussi E10

    Thanks guys 😀
    would give you all a big sloppy kiss xxxxx ( manly one’s) 😉
    Thanks for the quick replies

    in reply to: INDESIT R 24 #298501
    washermanuk
    Participant

    Re: INDESIT R 24

    This should be in The most annoying things our lovely customers do!!!! 😆

    in reply to: Beko Condensor Dryer/Hand Shredder DRCS65w H #298826
    washermanuk
    Participant

    Re: Beko Condensor Dryer/Hand Shredder DRCS65w H

    Hi matey did one about week ago took the machines back panel off completely leaving drum insitu, I think there was a screw somewhere holding either pump or cover?

    in reply to: Whirlpool WH3LSC8255EQ1 #298867
    washermanuk
    Participant

    Re: Whirlpool WH3LSC8255EQ1

    Hi matey! Is the pump running? When you fitted the new pump did you notice a adaptor on the end of the motor shaft, its like a plastic sleeve
    the motor shaft and pump drive are different sizes!!!
    hope this helps?

    in reply to: Bosch SGV5613GB/12 Water not heating ? #298595
    washermanuk
    Participant

    Re: Bosch SGV5613GB/12 Water not heating ?

    Glad to help! Sorry i didnt reply to your help in removing Pcb, computer went down :rolls:
    Happy dishwashing 😉

    in reply to: Bosch SGV5613GB/12 Water not heating ? #298591
    washermanuk
    Participant

    Re: Bosch SGV5613GB/12 Water not heating ?

    Hi matey a most common problem is a dry joint on the pcb board should see a seperate connector with two wires, one is red i think? hope this helps
    power off please and beware of the sharp metal edges 😉

    in reply to: Whats the most annoying thing customers do? #107732
    washermanuk
    Participant

    Re: Whats the most annoying thing customers do?

    I thought i was the only one to get these customers!
    nice to know im not alone 😉
    A very good stress relieving topic 😀
    THANK YOU ALL!!!!!!!

    in reply to: Whats the most annoying thing customers do? #107728
    washermanuk
    Participant

    Re: Whats the most annoying thing customers do?

    Today i had an “Any time” call booked by the customer! Then he rings asking “when will i call”.
    Sheer madness :rolls:

    in reply to: MEGGER #298290
    washermanuk
    Participant

    Re: MEGGER

    EVERSHED & VIGNOLES LTD HAND GENERATOR – VINTAGE 1918
    on ebay if your a collector 😉

    in reply to: Whats the most annoying thing customers do? #107712
    washermanuk
    Participant

    Re: Whats the most annoying thing customers do?

    Have you had the customer that makes a brew in front of you and drinks it while your repairing their machine and not even offering you one!!!!! 😯

Viewing 15 posts - 136 through 150 (of 165 total)