Washman

Forum Replies Created

Viewing 15 posts - 571 through 585 (of 894 total)
1 2 3 … 38 39 40 … 58 59 60
  • Author
    Posts
  • July 13, 2007 at 3:06 pm in reply to: Wf860 not filling correctly #220946
    Washman
    Participant

    Re: Wf860 not filling correctly

    Hi

    Do not worry about hot water going into machine as most washes do not fill with hot water as your hot supply will be to hot for most washes. Alot of machines these days are cold fill only, all machines will heat the water to correct temperature any way.

    Mike

    July 12, 2007 at 6:19 pm in reply to: Beko fridge #220739
    Washman
    Participant

    Re: Beko fridge

    Hi

    The heat from the compressor should evaporate water from the drip tray.
    There may be water in the tray all the time depending on operating conditions.

    Mike

    July 10, 2007 at 10:11 am in reply to: Servis – module burnt out #220479
    Washman
    Participant

    Re: Servis – module burnt out

    Hi

    The main connector blocks do burn out , when replacing pcb replace connector block with crimp terminals. And make sure all connectors on pcb are a tight fit

    Mike

    July 2, 2007 at 6:16 pm in reply to: Zanussi Freezone – freezer working, fridge not working #219426
    Washman
    Participant

    Re: Zanussi Freezone – freezer working, fridge not working

    Hi

    Remove salad drawer from fridge and it should be on the side of fridge

    Mike

    July 2, 2007 at 3:15 pm in reply to: Zanussi Freezone – freezer working, fridge not working #219424
    Washman
    Participant

    Re: Zanussi Freezone – freezer working, fridge not working

    Hi

    Model number and PNC number please

    Mike

    July 2, 2007 at 10:52 am in reply to: Belling XOU 252 SF “dead”? #219310
    Washman
    Participant

    Re: Belling XOU 252 SF “dead”?

    Hi

    Check the timer is set to manual and not auto.

    Mike

    June 30, 2007 at 2:30 pm in reply to: diplomat fault code #219102
    Washman
    Participant

    Re: diplomat fault code

    Hi

    Model and Serial Numbers please

    June 30, 2007 at 2:17 pm in reply to: proline spares #219104
    Washman
    Participant

    Re: proline spares

    Hi

    According to info this is Tecnogas / Servis

    base element 1800w 524012300
    grill element 524017400
    fan element supersedes to 524022100

    Mike

    June 29, 2007 at 5:44 pm in reply to: dh 102 overfilling #219023
    Washman
    Participant

    Re: dh 102 overfilling

    Hi

    Never try to adjust a pressure switch, it is factory set , it is most likely a blockage in one of the tubes going to the pressure switch , and needs cleaning out.

    Mike

    June 27, 2007 at 12:17 pm in reply to: NEB FE8622EX oven door hinges #218642
    Washman
    Participant

    Re: NEB FE8622EX oven door hinges

    HI

    Cheers Andy an order has been sent to you.

    Mike

    June 26, 2007 at 4:02 pm in reply to: Zanussi FL 1085 stall #218485
    Washman
    Participant

    Re: Zanussi FL 1085 stall

    Hi

    It could be the cold fill valve not opening or cold tap turned off.

    June 23, 2007 at 5:28 pm in reply to: Bosch Fridge Freezer, freezer has stopped working #218162
    Washman
    Participant

    Re: Bosch Fridge Freezer, freezer has stopped working

    Hi :waving:

    June 23, 2007 at 5:24 pm in reply to: Bosch Fridge Freezer, freezer has stopped working #218160
    Washman
    Participant

    Re: Bosch Fridge Freezer, freezer has stopped working

    Hi

    You will need to turn freezer off and defrost it completely for 48 hours before switching back on ,as the freezing coil is most likely frozen up. Then keep an eye on freezer , if the same problem happens in a week or so then you most likely have a defrost heater or timer fault.

    washman

    June 22, 2007 at 7:44 pm in reply to: Electrolux ES6633I fridge – compressor running constantly #218098
    Washman
    Participant

    Re: Electrolux ES6633I fridge – compressor running constantl

    Hi

    As long as you have the thin layer of ice and not a thick layer then it is most likely working ok. And if you are opening and closing the door alot then compressor will run alot . remember each time you open the door the cold air falls out of the fridge so when you close the door it has to cool the air again. fridge and freezer compressors do run for alot longer than they are off.

    Mike

    June 22, 2007 at 1:56 pm in reply to: servis quartz 600 drum problem #218055
    Washman
    Participant

    Re: servis quartz 600 drum problem

    Hi

    Drum spider has broken possibly. Only way to sure would be total strip down. Model number of machine would be a help.

  • Author
    Posts
Viewing 15 posts - 571 through 585 (of 894 total)
1 2 3 … 38 39 40 … 58 59 60